preview
Woodworking tools chest. Wanted to make it look somewhat antique but got carried away.


Woodworking tools chest. Wanted to make it look somewhat antique but got carried away.


Not on this instance? Enter your own instance's domain to go straight to following c/woodworking@lemmy.ca there.
Woodworking tools chest. Wanted to make it look somewhat antique but got carried away.


Woodworking tools chest. Wanted to make it look somewhat antique but got carried away.


I found a hand plane at the thrift store. I think this is a #4 smoothing plane, which I hope to use for finishing. But before that, it’s quite clear that I’m going to have to clean this up a bit by removing the rust and making it look a bit prettier.
Any advice y’all have for how I might start restoring this?
I found a hand plane at the thrift store. I think this is a #4 smoothing plane, which I hope to use for finishing. But before that, it’s quite clear that I’m going to have to clean this up a bit by removing the rust and making it look a bit prettier.
Any advice y’all have for how I might start restoring this?
The eyes are a bit big but I think it’s cute
It’s a melanoid axolotl as a Christmas present for a friend’s kid who loves them but can’t play with them because of the whole being in a glass tank thing
Walnut, brass, and some mystery reddish hardwood for the gills


The eyes are a bit big but I think it’s cute
It’s a melanoid axolotl as a Christmas present for a friend’s kid who loves them but can’t play with them because of the whole being in a glass tank thing
Walnut, brass, and some mystery reddish hardwood for the gills


Made these years ago trying to use up offcuts.
Just simple blocks with holes drilled. They actually come in handy and could be good gift ideas.
Made these years ago trying to use up offcuts.
Just simple blocks with holes drilled. They actually come in handy and could be good gift ideas.
(it’s a training dagger for a friend who does medieval swordfighting stuff, though it’s also got a good magic wand energy to it)


(it’s a training dagger for a friend who does medieval swordfighting stuff, though it’s also got a good magic wand energy to it)


I’ll give you guys a rundown.
You’ll need some things: -sharp block plane -painters tape -flat plate -various adhesive backed sandpaper -hand drill -food grade mineral oil -1/4” x 5/16” figured hardwood you pilfered from work -the PrettyWhooped Chopstick Jig (drawings available upon request)
Okay, here’s the recipe:
Fit hardwood stock into slot (1). With a block plane that’s been offset with three strips of painter’s tape on both sides, shave stock until you can’t remove anymore.
Remove the stock (I use a 1/8” chisel) and flip. Remove two strips of tape from plane, and shave stock.
Insert stock into slot (2). Be sure stock sits against back wall of slot. Shave stock. Rotate stock 90° and shave.
Rotate stock another 90° and insert into slot (3). As before, ensure stock is against back wall. Shave. Rotate 90°. Shave.
Place stock in slot (4) and shave the exposed corner. Rotate 90° and shave. Repeat for all corners.
Move stock to slot (5). Shave and repeat for all corners. You should now have a chopstick that measures 1/4” square at the base and tapers halfway to a 5/32” octagon at the tip with chamfered corners all around.
Clean up any rough surfaces with your flat plate and sandpaper.
Wrap base in a few layers of painter’s tape and mount it in your hand drill. The tape should protect your workpiece, but still be careful to not over tighten. Carefully turn the drill and run the tip of your work piece against your sandpapered flat plate. You’ll want to support it with your free hand, but if some correctly, you should get a slight round chamfer.
Remove tape and clean up any marks left by the drill by again sanding with the flat plate. Round over the remaining sharp corners at the base by dragging the chopstick against the flat plate in a rolling motion.
Repeat step 1-9 to make a mate and finish by soaking in mineral oil for an hour or so. Let cure to manufacturer’s recommendations.
Make sure you’re always rotating the same direction and keep your plane sharp. Shouldn’t take more than 10-15 minutes a stick.
Enjoy!
I’ll give you guys a rundown.
You’ll need some things: -sharp block plane -painters tape -flat plate -various adhesive backed sandpaper -hand drill -food grade mineral oil -1/4” x 5/16” figured hardwood you pilfered from work -the PrettyWhooped Chopstick Jig (drawings available upon request)
Okay, here’s the recipe:
Fit hardwood stock into slot (1). With a block plane that’s been offset with three strips of painter’s tape on both sides, shave stock until you can’t remove anymore.
Remove the stock (I use a 1/8” chisel) and flip. Remove two strips of tape from plane, and shave stock.
Insert stock into slot (2). Be sure stock sits against back wall of slot. Shave stock. Rotate stock 90° and shave.
Rotate stock another 90° and insert into slot (3). As before, ensure stock is against back wall. Shave. Rotate 90°. Shave.
Place stock in slot (4) and shave the exposed corner. Rotate 90° and shave. Repeat for all corners.
Move stock to slot (5). Shave and repeat for all corners. You should now have a chopstick that measures 1/4” square at the base and tapers halfway to a 5/32” octagon at the tip with chamfered corners all around.
Clean up any rough surfaces with your flat plate and sandpaper.
Wrap base in a few layers of painter’s tape and mount it in your hand drill. The tape should protect your workpiece, but still be careful to not over tighten. Carefully turn the drill and run the tip of your work piece against your sandpapered flat plate. You’ll want to support it with your free hand, but if some correctly, you should get a slight round chamfer.
Remove tape and clean up any marks left by the drill by again sanding with the flat plate. Round over the remaining sharp corners at the base by dragging the chopstick against the flat plate in a rolling motion.
Repeat step 1-9 to make a mate and finish by soaking in mineral oil for an hour or so. Let cure to manufacturer’s recommendations.
Make sure you’re always rotating the same direction and keep your plane sharp. Shouldn’t take more than 10-15 minutes a stick.
Enjoy!
Got a mini-lathe for Christmas last year and needed something to put it on. Hundreds of spinning tops and mushrooms later, I’m pretty sure it was worth it. Here’s a couple other things from my lathe.


Got a mini-lathe for Christmas last year and needed something to put it on. Hundreds of spinning tops and mushrooms later, I’m pretty sure it was worth it. Here’s a couple other things from my lathe.


Measure twice…cut once…swear…repeat

Measure twice…cut once…swear…repeat

So, I had kind of a mishap a few weeks ago: the original bridge of my Vihuela de Mano ripped clean off when I tried to bring the strings to tension. Might be that the glue surface was too cold or the natural oil in the rosewood prevented a proper bond. Or the glue surface was simply too small for 42kg of string tension.

After some consideration, I decided to redesign the bridge to be more of a lute style (with 3x the glue surface of the original bridge), while trying to preserve the original look. It’s now made of cherry, with ebony and ivory inlays.
So, I had kind of a mishap a few weeks ago: the original bridge of my Vihuela de Mano ripped clean off when I tried to bring the strings to tension. Might be that the glue surface was too cold or the natural oil in the rosewood prevented a proper bond. Or the glue surface was simply too small for 42kg of string tension.

After some consideration, I decided to redesign the bridge to be more of a lute style (with 3x the glue surface of the original bridge), while trying to preserve the original look. It’s now made of cherry, with ebony and ivory inlays.
I’m building a shed, and want a large single door on the end. It’s 47" wide by 74" high (roughly 4’x6’ or 120cm x 180cm), framed like a regular house door would be (header of two 2x boards with plywood sandwiched; joist and trimmer on each side). I’d like the door to avoid sagging, and also be strong enough so when kids inevitably climb on it that’s fine too.
I see lots of patterns for shed doors, for example (from secrets-of-shed-building) the zig zag, with a pair of triangles bearing weight down to the hinge edge:

Or (from artofit but are they the new pinterest or something?) the high single diagonal:

Or rectangles, or exes on the lower or both halves. Does the variety mean it doesn’t really matter?
The shed has plywood sheathing, and I’m planning to have a single panel of plywood sheathing on the door, does that provide enough shear stiffness?
And I’ll probably use 2x4 framing on the back/inside of the door, maybe lap joints for fun though most people seem to just do butt joints, probbly flat against the door though I see some folks putting the 2x4s edge against the door like they’re just framing more wall.
Any experience with sagging or successful doors very welcome, or structural theory to apply here! Thanks in advance.
I’m building a shed, and want a large single door on the end. It’s 47" wide by 74" high (roughly 4’x6’ or 120cm x 180cm), framed like a regular house door would be (header of two 2x boards with plywood sandwiched; joist and trimmer on each side). I’d like the door to avoid sagging, and also be strong enough so when kids inevitably climb on it that’s fine too.
I see lots of patterns for shed doors, for example (from secrets-of-shed-building) the zig zag, with a pair of triangles bearing weight down to the hinge edge:

Or (from artofit but are they the new pinterest or something?) the high single diagonal:

Or rectangles, or exes on the lower or both halves. Does the variety mean it doesn’t really matter?
The shed has plywood sheathing, and I’m planning to have a single panel of plywood sheathing on the door, does that provide enough shear stiffness?
And I’ll probably use 2x4 framing on the back/inside of the door, maybe lap joints for fun though most people seem to just do butt joints, probbly flat against the door though I see some folks putting the 2x4s edge against the door like they’re just framing more wall.
Any experience with sagging or successful doors very welcome, or structural theory to apply here! Thanks in advance.
The design is pretty straight forward: a V notch bisected by a straightedge, but aligning it during glue up was tricky. If I make another I’ll think about fitting the straightedge into a rabbet or something so it’s not sliding around.
The design is pretty straight forward: a V notch bisected by a straightedge, but aligning it during glue up was tricky. If I make another I’ll think about fitting the straightedge into a rabbet or something so it’s not sliding around.
Am gonna start wearing welder’s gloves…might stop me from leaving blood samples all over my work :(
Am gonna start wearing welder’s gloves…might stop me from leaving blood samples all over my work :(
I talked to a neighbor I met in the neighborhood workshop, he told me he had around 2000 mm x 150 mm, each dried logs of cherry and juniper. The juniper I figure I can carve into kitchen utensils, and the cherry can be used for tool handles.
The problem is I’m a complete beginner to woodworking. I have no clue how I should go about preparing the stock for this. I have a set of chisels, a Stanley No.5, Stanley No.4½, all of which I have the ability to sharpen. I have no hatchets, froes, or logging chisels.
He said he was gonna throw this out soon, and hardwood is hard to come by where I live.
EDIT: To clarify, I share the workshop with this neighbor, and a few other neighbors. The wood has been stored in this location for several years, and I would keep storing it here. Thank you for all of your replies!
I talked to a neighbor I met in the neighborhood workshop, he told me he had around 2000 mm x 150 mm, each dried logs of cherry and juniper. The juniper I figure I can carve into kitchen utensils, and the cherry can be used for tool handles.
The problem is I’m a complete beginner to woodworking. I have no clue how I should go about preparing the stock for this. I have a set of chisels, a Stanley No.5, Stanley No.4½, all of which I have the ability to sharpen. I have no hatchets, froes, or logging chisels.
He said he was gonna throw this out soon, and hardwood is hard to come by where I live.
EDIT: To clarify, I share the workshop with this neighbor, and a few other neighbors. The wood has been stored in this location for several years, and I would keep storing it here. Thank you for all of your replies!


I received a bottle opener, and I wanted it to be on display. The stand consists of two pieces of pear wood. The axe I oiled, and the base I will leave untreated.


I received a bottle opener, and I wanted it to be on display. The stand consists of two pieces of pear wood. The axe I oiled, and the base I will leave untreated.
A while back I was gifted some old classroom side tables the owner no longer needed. They came painted; I don’t know what kind of paint it was, but it was entirely resistant to citristrip. After finally working that out I painstakingly sanded the paint out from every nook and crevice with a dremel until I was confident it was clean. I dried it out, sanded it, and prepared to finally finish up.
Today I stained. Coat of wood conditioner, wait around half an hour, coat of stain. Maybe 3 more hours (instructions call for minimum 2) and a second coat. I was dismayed to find that while the top veneer stained beautifully, the legs came out splotchy. It looks like there was an invisible coat of primer on there or something that prevented the stain from taking. I am confident this is not the result of poor stain application; it was apparent that it wasn’t taking while I was brushing it. The band around the top also came out significantly darker than the top.
The band I know I probably can’t do anything about. It’s annoying but I can live with it. The legs are a different story. Is there anything I can do to make them take the stain more evenly?
P.S. I also had an entirely different table made of some kind of hardwood that I did. It took very evenly but didn’t color much even with two coats. I know with hardwoods that’s somewhat inevitable. Any tricks to make it take more, or do I just need to be happy with it?
A while back I was gifted some old classroom side tables the owner no longer needed. They came painted; I don’t know what kind of paint it was, but it was entirely resistant to citristrip. After finally working that out I painstakingly sanded the paint out from every nook and crevice with a dremel until I was confident it was clean. I dried it out, sanded it, and prepared to finally finish up.
Today I stained. Coat of wood conditioner, wait around half an hour, coat of stain. Maybe 3 more hours (instructions call for minimum 2) and a second coat. I was dismayed to find that while the top veneer stained beautifully, the legs came out splotchy. It looks like there was an invisible coat of primer on there or something that prevented the stain from taking. I am confident this is not the result of poor stain application; it was apparent that it wasn’t taking while I was brushing it. The band around the top also came out significantly darker than the top.
The band I know I probably can’t do anything about. It’s annoying but I can live with it. The legs are a different story. Is there anything I can do to make them take the stain more evenly?
P.S. I also had an entirely different table made of some kind of hardwood that I did. It took very evenly but didn’t color much even with two coats. I know with hardwoods that’s somewhat inevitable. Any tricks to make it take more, or do I just need to be happy with it?
I put poly on it, then sanded it off, then procrastinated for a couple months, but today I decided it’s going to be done.
So I put a quick coat of 50/50 beeswax and mineral oil and called it a day

I put poly on it, then sanded it off, then procrastinated for a couple months, but today I decided it’s going to be done.
So I put a quick coat of 50/50 beeswax and mineral oil and called it a day

No trees were harmed in the making of this video (they were all felled in a big windstorm).
No trees were harmed in the making of this video (they were all felled in a big windstorm).
Used up a perfect piece of scrap, too. Now I’ll have to make a glueup for the body of the righty version.
I’m going to leave the lefty 90% finished and do the final 10% if I ever find a need for it.
Used up a perfect piece of scrap, too. Now I’ll have to make a glueup for the body of the righty version.
I’m going to leave the lefty 90% finished and do the final 10% if I ever find a need for it.
Ebony/Boxwood. I did this with a CNC - but pointy inlays are still quite tricky.
Ebony/Boxwood. I did this with a CNC - but pointy inlays are still quite tricky.
Probably not really necessary given how shallow it is, but I had fun hand chiseling a very slight birdsmouth for some shed rafters. After some practice (and sharpening), I could get most of the material in one cut. Demos I saw all used a circular saw, so thought I’d share something different.
Probably not really necessary given how shallow it is, but I had fun hand chiseling a very slight birdsmouth for some shed rafters. After some practice (and sharpening), I could get most of the material in one cut. Demos I saw all used a circular saw, so thought I’d share something different.
Made a few line carvings similar to my previous post and trying to work out how to finish them. So far experimenting with Danish oil and Tudor oak coloured briwax. I also probably need to get some finer grit sandpaper at some point.
Carve straight into old wood, the carved lines are pale compared to the surrounding weathered wood. The lines are distinctive and easy to see.
Same as above followed by sanding and oiling, the lined are far less visible in comparison. Adding the wax and it might be a slight improvement but still not as clear as it was initially.
Attached image - Quick test this morning, sanding the wood then carving and applying wax, no oil. Some patches have held the wax/dark colouring better than others after wiping it down.
I am considering next trying to sand and oil the wood, then carve it and then wax it. Maybe a very gentle sanding before waxing if necessary but trying to keep most of the oil layer.
Trying to get the carved groves to be darker than the surrounding surface wood. Only got a few more bits of flat wood that don’t have nails or staples in them, or too many cracks and splits.
Made a few line carvings similar to my previous post and trying to work out how to finish them. So far experimenting with Danish oil and Tudor oak coloured briwax. I also probably need to get some finer grit sandpaper at some point.
Carve straight into old wood, the carved lines are pale compared to the surrounding weathered wood. The lines are distinctive and easy to see.
Same as above followed by sanding and oiling, the lined are far less visible in comparison. Adding the wax and it might be a slight improvement but still not as clear as it was initially.
Attached image - Quick test this morning, sanding the wood then carving and applying wax, no oil. Some patches have held the wax/dark colouring better than others after wiping it down.
I am considering next trying to sand and oil the wood, then carve it and then wax it. Maybe a very gentle sanding before waxing if necessary but trying to keep most of the oil layer.
Trying to get the carved groves to be darker than the surrounding surface wood. Only got a few more bits of flat wood that don’t have nails or staples in them, or too many cracks and splits.
Just got a dremel for an unrelated job and thought I should do something fun with it. Got a large bundle of cheap off brand bits as I don’t really know which ones are going to be most useful.
Using a scrap offcut of wood, there are still some rusty nails in it! This morning I wanted to practice carving straight and curved lines in the wood. It isn’t quite as easy as I thought, the wood grain changes the amount of resistance to movement and can push it to the side or slow down how fast its cutting.
The board is about 1.5cm thick, I also tried using one of the cutting discs, it seemed to cut alright but broke in half when I turned the dremel off. Got over 100 of them though. This board might be a little thick to use with these small cutting discs, pretty sure I would need the larger ones but I don’t see any in the set I bought.
Once I feel more confident in holding the dremel steady I would like to try making something decorative. Probably start with a coaster as that is something small to get started with. Then look at oils for it too. Leaning towards plywood as it is more affordable, although this scrap wood is free and hasn’t rotten too much yet. Might be worth sanding it to see what it feels like.
Just got a dremel for an unrelated job and thought I should do something fun with it. Got a large bundle of cheap off brand bits as I don’t really know which ones are going to be most useful.
Using a scrap offcut of wood, there are still some rusty nails in it! This morning I wanted to practice carving straight and curved lines in the wood. It isn’t quite as easy as I thought, the wood grain changes the amount of resistance to movement and can push it to the side or slow down how fast its cutting.
The board is about 1.5cm thick, I also tried using one of the cutting discs, it seemed to cut alright but broke in half when I turned the dremel off. Got over 100 of them though. This board might be a little thick to use with these small cutting discs, pretty sure I would need the larger ones but I don’t see any in the set I bought.
Once I feel more confident in holding the dremel steady I would like to try making something decorative. Probably start with a coaster as that is something small to get started with. Then look at oils for it too. Leaning towards plywood as it is more affordable, although this scrap wood is free and hasn’t rotten too much yet. Might be worth sanding it to see what it feels like.
CNC-cutting the sides to shape before bending worked surprisingly well. I had left 10mm extra at each end, but that turned out to be unnecessary. The back will have a 3000mm radius and the top will be bent slightly inwards for stability.
CNC-cutting the sides to shape before bending worked surprisingly well. I had left 10mm extra at each end, but that turned out to be unnecessary. The back will have a 3000mm radius and the top will be bent slightly inwards for stability.
I oiled it up according to the instructions, unfortunately it takes a month to cure.
I’m planning on putting polyurethane or some other film finish on top because the oil is quite dull as is. Maybe I’ll try burnishing it. I dunno.
I oiled it up according to the instructions, unfortunately it takes a month to cure.
I’m planning on putting polyurethane or some other film finish on top because the oil is quite dull as is. Maybe I’ll try burnishing it. I dunno.
Made using some oak scrap.

Hand tools for most of it. Drill press was useful to get the depth of the counter sink for the screws’ shoulders.

Made using some oak scrap.

Hand tools for most of it. Drill press was useful to get the depth of the counter sink for the screws’ shoulders.

Imperfections were all made with hand tools except for the sanding
Imperfections were all made with hand tools except for the sanding
The ones with the grain going the wrong way are cutting board cut offs. Pretty wood, why waste. More than likely just decorative. The standing one was a gift to the guy making the cutting boards.





The ones with the grain going the wrong way are cutting board cut offs. Pretty wood, why waste. More than likely just decorative. The standing one was a gift to the guy making the cutting boards.





The base is dovetailed at the corners and the uprights are lapped in. I have to complicate everything.
The base is dovetailed at the corners and the uprights are lapped in. I have to complicate everything.
Hello everybody,
My dining table made of recycled wood need a refreshing. After planing, what finishes would you recommend? I’d like it to be easy to clean and have a matte finish.
Thanks !

Hello everybody,
My dining table made of recycled wood need a refreshing. After planing, what finishes would you recommend? I’d like it to be easy to clean and have a matte finish.
Thanks !

Most stressful moments in my life:
But actually, gluing is so goddamn stressful to me.
Leg #1, my golden boy, worked perfectly, the glue looked good, the toothpick went in with just the right amount of friction, just beautiful.
Then I go to do leg #3, the ugly-ass, stretch Armstrong looking motherfucker, and the toothpick snaps after it was already fully inserted into the leg. THEN, when I used a pliers to pull it out, the end just ripped off, so I ended up relying on the suction inherent in the joint and prayers.
I think it’ll all turn out okay.
^this is #1, my golden boy
^top leg here is fuck-ass #3
Update: having taken the time to look at these pictures, I realize how horrifically uneven the tops of the legs are and I want to burn it. I did the gluing in a huge rush and it shows :[
Most stressful moments in my life:
But actually, gluing is so goddamn stressful to me.
Leg #1, my golden boy, worked perfectly, the glue looked good, the toothpick went in with just the right amount of friction, just beautiful.
Then I go to do leg #3, the ugly-ass, stretch Armstrong looking motherfucker, and the toothpick snaps after it was already fully inserted into the leg. THEN, when I used a pliers to pull it out, the end just ripped off, so I ended up relying on the suction inherent in the joint and prayers.
I think it’ll all turn out okay.
^this is #1, my golden boy
^top leg here is fuck-ass #3
Update: having taken the time to look at these pictures, I realize how horrifically uneven the tops of the legs are and I want to burn it. I did the gluing in a huge rush and it shows :[
Got the legs matched to the body and the holes drilled for the toothpicks, it’s almost ready for gluing
Just gotta fix this

Once I get that wonky leg fixed and a final sanding with like 220 on everything, it’ll be time to glue
Got the legs matched to the body and the holes drilled for the toothpicks, it’s almost ready for gluing
Just gotta fix this

Once I get that wonky leg fixed and a final sanding with like 220 on everything, it’ll be time to glue
Since every leg is a little different and the tail section isn’t perfectly symmetrical, I have to basically custom fit each leg to its section of the fuselage
So I’m just using a tiny piece of sandpaper and the tip of my finger. Making them out of softwood is coming in handy, as removing material is pretty easy.
I also found that rubbing the leg up and down while applying pressure makes slightly shiny spots that I can then sand.
It’s a laborious but effective process

Since every leg is a little different and the tail section isn’t perfectly symmetrical, I have to basically custom fit each leg to its section of the fuselage
So I’m just using a tiny piece of sandpaper and the tip of my finger. Making them out of softwood is coming in handy, as removing material is pretty easy.
I also found that rubbing the leg up and down while applying pressure makes slightly shiny spots that I can then sand.
It’s a laborious but effective process

Tonight I was able to: drill pilot holes for the toothpicks I’m gonna use to anchor the legs for gluing, slim down the top taper a little, and round off the nose that everyone so emphatically reminded me was going to kill someone
I’m a little sad to see it go, but the tip now kinda closely resembles the tips of the legs, which is very satisfying, esthetically.
^test fitting on a spare length of dowel with a sanded down toothpick so it didn’t widen the pilot holes
Ended up using a 5/64" bit, with glue it’s the perfect fit that’s tight, but can be done by hand or maybe a little tap tap
Tonight I was able to: drill pilot holes for the toothpicks I’m gonna use to anchor the legs for gluing, slim down the top taper a little, and round off the nose that everyone so emphatically reminded me was going to kill someone
I’m a little sad to see it go, but the tip now kinda closely resembles the tips of the legs, which is very satisfying, esthetically.
^test fitting on a spare length of dowel with a sanded down toothpick so it didn’t widen the pilot holes
Ended up using a 5/64" bit, with glue it’s the perfect fit that’s tight, but can be done by hand or maybe a little tap tap
The proportions are odd, the legs look much smaller than i imagined them.
Also gotta fix the tearout, I’m thinking of just taking like an inch off the overall length when I round the tip, which will remove the tearout in the process
I also don’t have a fucking clue how I’m gonna clamp them for the glue-up. I’m considering gluing one at a time and using rubber bands. i dunno, let me know if you’ve got a better idea
The proportions are odd, the legs look much smaller than i imagined them.
Also gotta fix the tearout, I’m thinking of just taking like an inch off the overall length when I round the tip, which will remove the tearout in the process
I also don’t have a fucking clue how I’m gonna clamp them for the glue-up. I’m considering gluing one at a time and using rubber bands. i dunno, let me know if you’ve got a better idea
As the shape revealed itself, I decided I liked the look of landing legs more than chunky fins
Also, my plan to wrap sandpaper around the dowel to match the curve worked spectacularly, I’m very very pleased
Also, the shape of these legs got very complicated very quickly


As the shape revealed itself, I decided I liked the look of landing legs more than chunky fins
Also, my plan to wrap sandpaper around the dowel to match the curve worked spectacularly, I’m very very pleased
Also, the shape of these legs got very complicated very quickly


I have zero idea what I’m doing but I put together this workbench for $35 as a start!
I have zero idea what I’m doing but I put together this workbench for $35 as a start!
I’m gonna make the fin a little slimmer than it is currently, but the general shape works for me.
It’s currently made from SPF from home depot, but I’m debating making them out of more oak dowels, but that’ll be SO MUCH more work to carve out
Just spent 5 minutes using the proper tools, got the other two roughed out, as opposed to the 30-45 minutes it took with the box cutter

I’m gonna make the fin a little slimmer than it is currently, but the general shape works for me.
It’s currently made from SPF from home depot, but I’m debating making them out of more oak dowels, but that’ll be SO MUCH more work to carve out
Just spent 5 minutes using the proper tools, got the other two roughed out, as opposed to the 30-45 minutes it took with the box cutter

My toddler is obsessed with rockets at the moment, so I decided to use an extra length of dowel to make him a sturdy one.
I’m currently brainstorming the best way to attach the fins, figured I’d see if anyone here had any ideas
Currently, I’m thinking of cutting perpendicular grooves from the bottom that the fins will slot into, with each pair of fins being a solid piece. But keep in mind I haven’t made the fins yet, so that’s definitely not set in stone.
Modeling after the v-2 because it looks as stereotypical as a rocket can
My toddler is obsessed with rockets at the moment, so I decided to use an extra length of dowel to make him a sturdy one.
I’m currently brainstorming the best way to attach the fins, figured I’d see if anyone here had any ideas
Currently, I’m thinking of cutting perpendicular grooves from the bottom that the fins will slot into, with each pair of fins being a solid piece. But keep in mind I haven’t made the fins yet, so that’s definitely not set in stone.
Modeling after the v-2 because it looks as stereotypical as a rocket can
I am posting this to a woodworking community and a cooking community, because he does both in these videos. The tree goes into the food, and it is used to make tools that are used to prepare or enjoy the food.
From the description:
A lot of you have been asking me if I could venture into the world of making savory tree flavored stuff, so when I had an entire dead pear tree on my hands, …
I am posting this to a woodworking community and a cooking community, because he does both in these videos. The tree goes into the food, and it is used to make tools that are used to prepare or enjoy the food.
From the description:
A lot of you have been asking me if I could venture into the world of making savory tree flavored stuff, so when I had an entire dead pear tree on my hands, …
I got given an AI slop set of plans to sort out - admittedly with an apology and a “this doesn’t look right can you fix it” but eurghhh
A sample of the nonsense - I’m not sure I can make a 10nm brace, and I certainly don’t have any furby cactors
I got given an AI slop set of plans to sort out - admittedly with an apology and a “this doesn’t look right can you fix it” but eurghhh
A sample of the nonsense - I’m not sure I can make a 10nm brace, and I certainly don’t have any furby cactors
I constructed everything in Fusion360 and cut the wood layers on a CNC. The parchment layer was cut with a foil cutting machine.
Here are the individual layers:

I constructed everything in Fusion360 and cut the wood layers on a CNC. The parchment layer was cut with a foil cutting machine.
Here are the individual layers:

Feeling like I am over thinking. My horizontal pieces are level, and my pickets I figure I will keep a straight run until the grade requires I “step up” the next run. Should a run always be post to post? or is 5-8 pickets ok? The right side is me trying to see what it looks like with shorter runs. (i dont think i like it.)
Grade is enough that right side of pic would only be 4’ tall while left is 6’ Ish.
My adhd and lack of self esteem is over thinking this huh? Is “space from top of picket to horizontal piece consistent” a visual plus that is worth something too?
Feeling like I am over thinking. My horizontal pieces are level, and my pickets I figure I will keep a straight run until the grade requires I “step up” the next run. Should a run always be post to post? or is 5-8 pickets ok? The right side is me trying to see what it looks like with shorter runs. (i dont think i like it.)
Grade is enough that right side of pic would only be 4’ tall while left is 6’ Ish.
My adhd and lack of self esteem is over thinking this huh? Is “space from top of picket to horizontal piece consistent” a visual plus that is worth something too?
Cherry and walnut. Five coats of food grade tung oil. Worked great. Made the beans flat

Cherry and walnut. Five coats of food grade tung oil. Worked great. Made the beans flat

I needed a racket for some tennis like sport. Since the sport is kind of local to my area, there is only few offers for these rackets, and some have quite high waiting times. Since they are made from plywood anyway, I decided to make it myself.
The melamin plywood I picked was a pain to work with, and I fiddled quite a bit with tape on the wood, drill speeds and everything, to avoid tearing the surface. I still did on the back, propably pushing too hard, so I scraped off the first layer. The clean black melamin would have looked better I think, but at some point I got so annoyed that I’m happy I was able to make it at least look decent.

I needed a racket for some tennis like sport. Since the sport is kind of local to my area, there is only few offers for these rackets, and some have quite high waiting times. Since they are made from plywood anyway, I decided to make it myself.
The melamin plywood I picked was a pain to work with, and I fiddled quite a bit with tape on the wood, drill speeds and everything, to avoid tearing the surface. I still did on the back, propably pushing too hard, so I scraped off the first layer. The clean black melamin would have looked better I think, but at some point I got so annoyed that I’m happy I was able to make it at least look decent.
