preview
So for Friday night, myself and my friends got rather board.
And as the resident “Things collector” i got 2 Maxtor touch sense 2 external hardrives. However those who were alive in 2000’s know Maxtor went bankrupt and haven’t made hardrives for a very long time.
One of these drive i got BRAND NEW, in box at a flea market. sadly time got to the platters first, i spent a few hours trying to reformat or partition them and all i got was write errors. I tried different utility’s with no avail and decided to cut my losses, so i asked the boys what we should do with them? Immediately my friend had an idea, to bring out his 9mm and see how a hardrive would fair! We all took turns and they were pretty hard to hit (we made the mistake of drink soda before hand). We eventually landed some shots on the center of the drives and MAN it actually stopped 2 bullets!!!
going into this we all expected the disk to be unreadable after the fact, but didnt think the hardrives would stop a 9mm bullet!!
We then took the hdd’s apart after are volley of bullets, and alot of the chips were damaged and all the platters were bent. But when we took off the top case, it looked so freakin cool i had to keep it

So for Friday night, myself and my friends got rather board.
And as the resident “Things collector” i got 2 Maxtor touch sense 2 external hardrives. However those who were alive in 2000’s know Maxtor went bankrupt and haven’t made hardrives for a very long time.
One of these drive i got BRAND NEW, in box at a flea market. sadly time got to the platters first, i spent a few hours trying to reformat or partition them and all i got was write errors. I tried different utility’s with no avail and decided to cut my losses, so i asked the boys what we should do with them? Immediately my friend had an idea, to bring out his 9mm and see how a hardrive would fair! We all took turns and they were pretty hard to hit (we made the mistake of drink soda before hand). We eventually landed some shots on the center of the drives and MAN it actually stopped 2 bullets!!!
going into this we all expected the disk to be unreadable after the fact, but didnt think the hardrives would stop a 9mm bullet!!
We then took the hdd’s apart after are volley of bullets, and alot of the chips were damaged and all the platters were bent. But when we took off the top case, it looked so freakin cool i had to keep it

preview
So those who know me IRL or cyber stock me. Know that in my free time i do have a very small laser cutting business, i started off with a really crap diode laser and eventually made enough to purchase a full size C02 Laser.
Now one of the most important thing that machining has thought me. Is that WORK HOLDING IS BASED. Why indicate a shitty piece of bar stock each time when you can just make a jig/fixture and run thousands with minimal work. So i very much took this to heart and instead of spending 20 minutes to frame a coaster in my laser cutter to make sure it is 100% straight. I took a ratty piece of sheet metal (that i paid WAAAAY to much for $90USD) and made my “ghetto bed”.
now it was handcrafted the same way a child makes a macaroni picture. Very imprecise, and not flat at all i tried my best at making it flat but well, im a machinist not a metal worker. which truly shows my 1/1 piccaso’s masterpiece. So i hear you WHERE IS THIS GOING!!
this “ghetto bed” worked very well for small stuff, when family and friends would order something i would quickly throw in my jig load up my file and BAM its ready to go. This bed was purely a proof of concept, from the post i saw on light-burns forum of a guy doing something similar with sheet metal.
So fast foward 3 years later and i bought plate 3/4 plate stock (which i paid out the ass for) order it to size and draw up a CAD model.
a few thing i learned from the original “ghetto bed” was that the exhaust is underneath the bed and needed some way to quickly slurp up the smoke, for this i have a snorkel i am 3d printing and running downward (still work in progress as we speak) and secondly and most importantly! I wanted threading, i originally drilled 7/16 holes to which i just vaguely threaded bolts and nuts through. But now i have 1/4-20 spaces 1.30 inches across the bed, which will make setting up fixtures more solid and repeatable unlike the original bed. i did go with 1/4-20 for a few reasons, first off its standardized and very cheap for bolts, second and most importantly its a small hole. Which then allows me to drill and re-tap if i strip a thread and it also gives me alot of mounting holes. However having tons of holes were also a nightmare to hand tap and debur the backside.

The keen eyed among you may notice slots on the edges of the bed, i decided to go with slots purely because the original mounting holes are not concentric or symmetrical. So F it slots!
im very happy with the bed, i plan to paint it black to make it not reflective and have played around with the idea of open sourcing/selling bed like this, if people are intreasted of course!
So those who know me IRL or cyber stock me. Know that in my free time i do have a very small laser cutting business, i started off with a really crap diode laser and eventually made enough to purchase a full size C02 Laser.
Now one of the most important thing that machining has thought me. Is that WORK HOLDING IS BASED. Why indicate a shitty piece of bar stock each time when you can just make a jig/fixture and run thousands with minimal work. So i very much took this to heart and instead of spending 20 minutes to frame a coaster in my laser cutter to make sure it is 100% straight. I took a ratty piece of sheet metal (that i paid WAAAAY to much for $90USD) and made my “ghetto bed”.
now it was handcrafted the same way a child makes a macaroni picture. Very imprecise, and not flat at all i tried my best at making it flat but well, im a machinist not a metal worker. which truly shows my 1/1 piccaso’s masterpiece. So i hear you WHERE IS THIS GOING!!
this “ghetto bed” worked very well for small stuff, when family and friends would order something i would quickly throw in my jig load up my file and BAM its ready to go. This bed was purely a proof of concept, from the post i saw on light-burns forum of a guy doing something similar with sheet metal.
So fast foward 3 years later and i bought plate 3/4 plate stock (which i paid out the ass for) order it to size and draw up a CAD model.
a few thing i learned from the original “ghetto bed” was that the exhaust is underneath the bed and needed some way to quickly slurp up the smoke, for this i have a snorkel i am 3d printing and running downward (still work in progress as we speak) and secondly and most importantly! I wanted threading, i originally drilled 7/16 holes to which i just vaguely threaded bolts and nuts through. But now i have 1/4-20 spaces 1.30 inches across the bed, which will make setting up fixtures more solid and repeatable unlike the original bed. i did go with 1/4-20 for a few reasons, first off its standardized and very cheap for bolts, second and most importantly its a small hole. Which then allows me to drill and re-tap if i strip a thread and it also gives me alot of mounting holes. However having tons of holes were also a nightmare to hand tap and debur the backside.

The keen eyed among you may notice slots on the edges of the bed, i decided to go with slots purely because the original mounting holes are not concentric or symmetrical. So F it slots!
im very happy with the bed, i plan to paint it black to make it not reflective and have played around with the idea of open sourcing/selling bed like this, if people are intreasted of course!
preview
So I enjoyed r/Machining on Reddit, but Reddit kinda dead, so I decided to make a new community! Thanks for looking
feel free to post. -Edit I also want to say thanks for interacting and helping me out with identifying tools and stuff, I hope to learn a lot from you all, and I hope you can learn something from me as well Cheers!!!
So I enjoyed r/Machining on Reddit, but Reddit kinda dead, so I decided to make a new community! Thanks for looking
feel free to post. -Edit I also want to say thanks for interacting and helping me out with identifying tools and stuff, I hope to learn a lot from you all, and I hope you can learn something from me as well Cheers!!!