0

Electricity basics - Induction

preview

An electron flow - a current - in a conductor can influence the electron spin in neighboring conductors, which in turn yields magnetic fields, as we saw with the solenoid. However, this relationship goes both ways. Magnetic fields can also cause electron flow: if we move a conductor through a magnetic field, the magnetic field will push the electrons in the conductor in a certain direction. Recall that we learned in previous posts that it is voltage that makes current flow. The push - or pressure, if you will - that we exert on the electrons in the conductor by moving it through a magnetic field is also voltage. However, contrary to the voltage that we observed in earlier posts, this voltage is not caused by the difference between two differently charged nodes, as with batteries. In the case, voltage is caused by a force called electromotive force . The end goal - or rather, the result - is nevertheless the same: a current occurs! Now, if we move the conductor through the magnetic field in the opposite direction, the polarity of the voltage and the direction of the current change too. This phenomenon, when a magnetic field influences a conductor so that electric potential occurs, is called induction . One prerequisite for induction is that either the magnetic field or the conductor actually moves.

Y5xrbNQiTWTU4T5.jpg
Source: https://adityaabeysinghepresentations.blogspot.com/2013/11/electromagnetic-induction.html?m=1 (2026-09-09)

Current and voltage that regularly changes direction and polarity is called alternating current, shortened AC, and the opposite is called direct current, or DC.

The magnitude of the induced voltage is subject to:

  • the length of the conductor that “cuts through” the magnetic field lines
  • the velocity at which the field lines are “cut”
  • the density of the magnetic field

If the conductor in which we have induced voltage is part of a closed circuit, the voltage is going to drive current through the circuit. As we already know - both from earlier posts but also from above - current causes magnetic fields to appear around the conductor that leads it. This means that there are two magnetic fields present at induction: one between the poles of the magnet that induces the voltage/current and one around the conductor that we move back and forth between the poles of the magnet. The direction of the induced current - and thus the direction of rotation of the magnetic fields around its conductor - is such that it “collides” with the direction of movement that is otherwise required for the induction to happen. This “collision” or “friction” is similar to what happens when you try to make two magnets of the same polarity touch: they repel! This phenomenon is described in greater detail in Lenz’s Law, but to summarize: the kinetic energi required to move either the magnetic fields past the conductor or the conductor through the magnetic fields is converted into electric energy.

To be continued. Meanwhile:

  1. Are there better expressions in English than “cut” and “cut through” magnetic fields?
  2. I translated the book to saying “density of the magnetic field”, but I am unsure whether this is correct in English. Would “intensity” be better?
  3. I feel uneasy (really intrigued!) when the book makes a connection between kinetic and electric energy, because it makes me wonder: are there conversion tables or the likes? As in, how much power in watts, joules or even calories yields how much electric energy? Wouldn’t that depend on the mass of the, say, inductor that is forced through the magnetic fields? Wouldn’t the strength of the magnetic fields also be a determining factor? Leading, in my head, to the definition: if a conductor of X mass moves through magnetic fields of Y strength with the velocity of Z, then V volts and A amperes are induced.
  4. In other places, I have seen “potential difference”, “electromotive force” and “voltage” being used interchangeably. But after reading the section about induction in this book, it does make me want to separate at the very least the phrases that distinguish how voltage is achieved: by opposite charges (such as in a battery) or by electromotive force as seen in induction…
  5. I was absolutely blown away when I understood what induction is! So much of our appliances seem to be using this technology! Like, the spinning bikes at the gym? I can just imagine there being a bunch of magnets surrounding the wheel looking “outwards”, and pieces of iron all around the wheel itself looking “inward” and as I pedal, the rotation of the wheel induces voltage/current, which turns on the display?! Again, I’m so amped about this. 😆🩷

An electron flow - a current - in a conductor can influence the electron spin in neighboring conductors, which in turn yields magnetic fields, as we saw with the solenoid. However, this relationship goes both ways. Magnetic fields can also cause electron flow: if we move a conductor through a magnetic field, the magnetic field will push the electrons in the conductor in a certain direction. Recall that we learned in previous posts that it is voltage that makes current flow. The push - or pressure, if you will - that we exert on the electrons in the conductor by moving it through a magnetic field is also voltage. However, contrary to the voltage that we observed in earlier posts, this voltage is not caused by the difference between two differently charged nodes, as with batteries. In the case, voltage is caused by a force called electromotive force . The end goal - or rather, the result - is nevertheless the same: a current occurs! Now, if we move the conductor through the magnetic field in the opposite direction, the polarity of the voltage and the direction of the current change too. This phenomenon, when a magnetic field influences a conductor so that electric potential occurs, is called induction . One prerequisite for induction is that either the magnetic field or the conductor actually moves.

Y5xrbNQiTWTU4T5.jpg
Source: https://adityaabeysinghepresentations.blogspot.com/2013/11/electromagnetic-induction.html?m=1 (2026-09-09)

Current and voltage that regularly changes direction and polarity is called alternating current, shortened AC, and the opposite is called direct current, or DC.

The magnitude of the induced voltage is subject to:

  • the length of the conductor that “cuts through” the magnetic field lines
  • the velocity at which the field lines are “cut”
  • the density of the magnetic field

If the conductor in which we have induced voltage is part of a closed circuit, the voltage is going to drive current through the circuit. As we already know - both from earlier posts but also from above - current causes magnetic fields to appear around the conductor that leads it. This means that there are two magnetic fields present at induction: one between the poles of the magnet that induces the voltage/current and one around the conductor that we move back and forth between the poles of the magnet. The direction of the induced current - and thus the direction of rotation of the magnetic fields around its conductor - is such that it “collides” with the direction of movement that is otherwise required for the induction to happen. This “collision” or “friction” is similar to what happens when you try to make two magnets of the same polarity touch: they repel! This phenomenon is described in greater detail in Lenz’s Law, but to summarize: the kinetic energi required to move either the magnetic fields past the conductor or the conductor through the magnetic fields is converted into electric energy.

To be continued. Meanwhile:

  1. Are there better expressions in English than “cut” and “cut through” magnetic fields?
  2. I translated the book to saying “density of the magnetic field”, but I am unsure whether this is correct in English. Would “intensity” be better?
  3. I feel uneasy (really intrigued!) when the book makes a connection between kinetic and electric energy, because it makes me wonder: are there conversion tables or the likes? As in, how much power in watts, joules or even calories yields how much electric energy? Wouldn’t that depend on the mass of the, say, inductor that is forced through the magnetic fields? Wouldn’t the strength of the magnetic fields also be a determining factor? Leading, in my head, to the definition: if a conductor of X mass moves through magnetic fields of Y strength with the velocity of Z, then V volts and A amperes are induced.
  4. In other places, I have seen “potential difference”, “electromotive force” and “voltage” being used interchangeably. But after reading the section about induction in this book, it does make me want to separate at the very least the phrases that distinguish how voltage is achieved: by opposite charges (such as in a battery) or by electromotive force as seen in induction…
  5. I was absolutely blown away when I understood what induction is! So much of our appliances seem to be using this technology! Like, the spinning bikes at the gym? I can just imagine there being a bunch of magnets surrounding the wheel looking “outwards”, and pieces of iron all around the wheel itself looking “inward” and as I pedal, the rotation of the wheel induces voltage/current, which turns on the display?! Again, I’m so amped about this. 😆🩷
0

Electricity basics - The relationship between electricity and magnetism

preview

IMPORTANT NOTICE
I have no formal education related to electricity or any other branch within the natural sciences. I take no responsibility for the factual accuracy of the posts, comments or any other content within this community.

In previous posts, we have looked at electricity and magnetism separately. However, electricity and magnetism have a close relationship. When current flows through a conductor, magnetic fields appear around the conductor. These are not the same kind of magnetic fields as those that emanate from permanent magnets, which are generated by electron spin. Instead, they are generated by the movement of electrons in the conductor. If the current stops, the magnetic field disappears.

The magnetic fields that are generated around a conductor when they carry current rotate around the exterior of the conductor in certain directions: they rotate clockwise, seen in the direction of the current/electron flow.

The direction of rotating magnetic fields in relation to the direction of current:
ihLCFVWmth3r3X5.jpg
Source: https://micro.magnet.fsu.edu/electromag/electricity/generators/ (2026-09-07)

The strength of the magnetic fields waxes and wanes in relation to the amount of current that flows through the conductor. The strength of the magnetic fields is weaker further away from the condctor. If you put a compass next to a single conductor that carries current, the arrow of the compass will position itself perpendicularly to the direction of the current, indicating the direction of the rotation of the magnetic fields.

Compasses next to a current carrying conductor:
hJITgTCNKhRPzI0.jpg
Source: https://storage.googleapis.com/dzprtnlcmuyjte/magnetic-field-around-a-wire-experiment.html (2026-09-07)

When looking at cross sections of wires, an “x” and a dot can be used to indicate the direction of current, together with the direction of the magnetic fields. The “x” indicates that the current flows away from the viewer, while the dot indicates that the current flows towards the viewer:
me4WFCEqyzfxBpJ.jpg
Source: https://www.slideserve.com/tracy/magnetic-field-of-electric-currents (2026-09-07)

The placement of conductors needs to be taken into consideration. Remember what we learned about electron spin! With that in mind, it is easier to understand that if two conductors whose current flows in opposite directions - and thus having magnetic fields rotating in opposite directions - are placed in close proximity to each other, the magnetic fields cancel each other out and no magnetic phenomena is observed outside the conductors. If, however, the conductors are placed so that current flows in the same direction, the magnetic fields amplify each other.
(Illustration needed.)

We can leverage these properties to create strong, non permanent magnets by twisting conductors into spirals or coils. The close proximity of the individual turns in the coil will yield the same effect as if we would have placed several separate conductors whose current flows in the same direction next to each other. We can enhance the strength of the magnetic fields even further by winding the conductor around a piece of iron, keeping the coil shape. The magnetic fields of the coil will then affect the direction of electron spin within the iron and make the iron magnetic. This, in turn, further enhances the magnetic fields of the coil. We call such magnets electromagnets or solenoids.

Simple solenoid construction:
cQSYqDJuImDVVXO.jpg
Source: https://www.skyfilabs.com/project-ideas/diy-electromagnet-stem-project-for-school-kids (2026-09-07)

Flow of magnetic fields in a simple solenoid:
SBvOiP9kzrnWHpY.jpg
Source: https://storage.googleapis.com/dtacjmqtkptxue/what-is-the-difference-between-electromagnet-and-magnet.html (2026-09-07)

One application of electromagnets are in so called relays. Relays are a way to use electromagnetism to turn a switch on and off instead of having to manually flip a switch. The conductor coil with the iron core that we talked about above are seen to the left, in the picture below. Just to the right of that, we see two flaps touching and releasing as current is being applied and removed. When current is applied, the iron core becomes magnetic, pulling the flap just above it downwards. This flap works as lever that actuates the other two flaps to the right.

TjARvTMEV3cCB9g.jpg

Go2ZBhKB29ReWhK.gif

To be continued.

IMPORTANT NOTICE
I have no formal education related to electricity or any other branch within the natural sciences. I take no responsibility for the factual accuracy of the posts, comments or any other content within this community.

In previous posts, we have looked at electricity and magnetism separately. However, electricity and magnetism have a close relationship. When current flows through a conductor, magnetic fields appear around the conductor. These are not the same kind of magnetic fields as those that emanate from permanent magnets, which are generated by electron spin. Instead, they are generated by the movement of electrons in the conductor. If the current stops, the magnetic field disappears.

The magnetic fields that are generated around a conductor when they carry current rotate around the exterior of the conductor in certain directions: they rotate clockwise, seen in the direction of the current/electron flow.

The direction of rotating magnetic fields in relation to the direction of current:
ihLCFVWmth3r3X5.jpg
Source: https://micro.magnet.fsu.edu/electromag/electricity/generators/ (2026-09-07)

The strength of the magnetic fields waxes and wanes in relation to the amount of current that flows through the conductor. The strength of the magnetic fields is weaker further away from the condctor. If you put a compass next to a single conductor that carries current, the arrow of the compass will position itself perpendicularly to the direction of the current, indicating the direction of the rotation of the magnetic fields.

Compasses next to a current carrying conductor:
hJITgTCNKhRPzI0.jpg
Source: https://storage.googleapis.com/dzprtnlcmuyjte/magnetic-field-around-a-wire-experiment.html (2026-09-07)

When looking at cross sections of wires, an “x” and a dot can be used to indicate the direction of current, together with the direction of the magnetic fields. The “x” indicates that the current flows away from the viewer, while the dot indicates that the current flows towards the viewer:
me4WFCEqyzfxBpJ.jpg
Source: https://www.slideserve.com/tracy/magnetic-field-of-electric-currents (2026-09-07)

The placement of conductors needs to be taken into consideration. Remember what we learned about electron spin! With that in mind, it is easier to understand that if two conductors whose current flows in opposite directions - and thus having magnetic fields rotating in opposite directions - are placed in close proximity to each other, the magnetic fields cancel each other out and no magnetic phenomena is observed outside the conductors. If, however, the conductors are placed so that current flows in the same direction, the magnetic fields amplify each other.
(Illustration needed.)

We can leverage these properties to create strong, non permanent magnets by twisting conductors into spirals or coils. The close proximity of the individual turns in the coil will yield the same effect as if we would have placed several separate conductors whose current flows in the same direction next to each other. We can enhance the strength of the magnetic fields even further by winding the conductor around a piece of iron, keeping the coil shape. The magnetic fields of the coil will then affect the direction of electron spin within the iron and make the iron magnetic. This, in turn, further enhances the magnetic fields of the coil. We call such magnets electromagnets or solenoids.

Simple solenoid construction:
cQSYqDJuImDVVXO.jpg
Source: https://www.skyfilabs.com/project-ideas/diy-electromagnet-stem-project-for-school-kids (2026-09-07)

Flow of magnetic fields in a simple solenoid:
SBvOiP9kzrnWHpY.jpg
Source: https://storage.googleapis.com/dtacjmqtkptxue/what-is-the-difference-between-electromagnet-and-magnet.html (2026-09-07)

One application of electromagnets are in so called relays. Relays are a way to use electromagnetism to turn a switch on and off instead of having to manually flip a switch. The conductor coil with the iron core that we talked about above are seen to the left, in the picture below. Just to the right of that, we see two flaps touching and releasing as current is being applied and removed. When current is applied, the iron core becomes magnetic, pulling the flap just above it downwards. This flap works as lever that actuates the other two flaps to the right.

TjARvTMEV3cCB9g.jpg

Go2ZBhKB29ReWhK.gif

To be continued.

0

Electricity basics - Magnetic equilibrium

preview

Magnetic fields are invisible force fields. They have direction and strength. They emanate from and return to the same point in space. But how do they emerge in the first place? Electrons not only orbit the atomic nucleus, but they also rotate around their own axis. This is called a “spin”. This rotation generates a magnetic field. No magnetic phenomena occur outside the atom.

Electron orbit and spin:
A5hispe2Q48wGra.png
https://www.researchgate.net/figure/Demonstrating-the-movement-of-the-electron-around-the-nucleus-58_fig2_368608080 (2026-09-06)

Within the same atom, electrons can rotate in different directions, or they can rotate in the same direction. When the electrons rotate in different directions, their individual magnetic fields cancel each other out and there is magnetic equilibrium. In many cases the same amount of electrons rotate in one direction as in the opposite direction.

Electrons spinning in different directions:
0cVaKQDIfWBc4Tx.jpg
Source: Ellära i teori och praktik, Leif Westlund and Gleerups Utbildning AB, 2012.

When all electrons rotate in the same direction, they enhance each other’s magnetic fields, instead of cancelling each other out. The material of which they are a part is then magnetic.

Electrons spinning in one direction (1):
GkqfsRyI6ivdIwq.jpg
Source: ibid.

Electrons spinning in one direction (2):
OwxZpb4EwVMtwQJ.jpg
Source: ibid.

A few materials, mostly minerals such as magnetite, are naturally magnetic. Materials, or objects, that have a constant magnetic field are called permanent magnets. Magnetic equilibrium - or the lack thereof - cannot change on its own. It can only change if influenced by an external force. For instance, permanent magnets can be artificially created, just as iron can be made temporarily magnetic. The ability to retain magnetism is called “remanence”. An example of a non permanent piece of metal that is often made magnetic is the tip of a screwdriver.

Magnetite:
fAHy4Io8KmRPgp8.jpg
Source: https://commons.wikimedia.org/w/index.php?curid=10139390 (2026-09-06)

Magnetic screwdriver:
A6h1WgVGQ9v4m7Q.jpg
Source: https://www.howtogeek.com/854142/is-it-safe-to-use-magnetic-screwdriver-in-a-pc/ (2026-09-26)

Magnets have two poles. In case of a bar magnet, they are called north/N-pole and south/S-pole. The magnetic flow emanates from the N-pole and returns through the S-pole. The magnetic flow is illustrated with field lines, which are imaginary, but a great way to start understanding magnetic fields and their directions. N-poles are often both illustrated and physically colored red, while S-poles are often white.

Bar magnet with illustrated field lines:
oBvBTlrGlICZnR0.jpg
Source: https://www.archyde.com/top-10-must-have-smartphones-right-now-galaxy-a56-xiaomi-15t-pro-more/ (2026-09-26)

Two materials of the same polarity can never be united and two materials of opposite polarity will attract each other with equal force.

zdhpvbfDtF6p74O.jpg
Source: https://stock.adobe.com/images/shows-a-diagram-of-magnetic-field-in-a-situation-of-repelling-and-attraction/112218437 (2026-09-06)

Magnetic fields can be manipulated or lead to flow in certain directions or in a more concentrated manner. For instance, by placing a bar magnet between the two ends of a U-shaped piece of iron.

(Illustration needed.)

To be continued. Meanwhile:

  1. I suppose “no magnetic phenomena occur outside the atom” is an oversimplification and what they really mean to say is that no magnetic fields are produced outside the atom?
  2. Do electrons really all rotate in the very same or the opposite three dimensional direction, or is this an oversimplification too and they really:

    • either rotate in a great variety of directions
    • or in similar directions
  3. By “united”, are they talking about nuclear fusion? I’m asking because I can physically push two N-poles together and make them touch if the magnet is small enough…

  4. It doesn’t sound or feel intuitive to say that opposite polarities will attract with equal force. What if one magnet has a mass of 20kg and the other 2 grams?

Magnetic fields are invisible force fields. They have direction and strength. They emanate from and return to the same point in space. But how do they emerge in the first place? Electrons not only orbit the atomic nucleus, but they also rotate around their own axis. This is called a “spin”. This rotation generates a magnetic field. No magnetic phenomena occur outside the atom.

Electron orbit and spin:
A5hispe2Q48wGra.png
https://www.researchgate.net/figure/Demonstrating-the-movement-of-the-electron-around-the-nucleus-58_fig2_368608080 (2026-09-06)

Within the same atom, electrons can rotate in different directions, or they can rotate in the same direction. When the electrons rotate in different directions, their individual magnetic fields cancel each other out and there is magnetic equilibrium. In many cases the same amount of electrons rotate in one direction as in the opposite direction.

Electrons spinning in different directions:
0cVaKQDIfWBc4Tx.jpg
Source: Ellära i teori och praktik, Leif Westlund and Gleerups Utbildning AB, 2012.

When all electrons rotate in the same direction, they enhance each other’s magnetic fields, instead of cancelling each other out. The material of which they are a part is then magnetic.

Electrons spinning in one direction (1):
GkqfsRyI6ivdIwq.jpg
Source: ibid.

Electrons spinning in one direction (2):
OwxZpb4EwVMtwQJ.jpg
Source: ibid.

A few materials, mostly minerals such as magnetite, are naturally magnetic. Materials, or objects, that have a constant magnetic field are called permanent magnets. Magnetic equilibrium - or the lack thereof - cannot change on its own. It can only change if influenced by an external force. For instance, permanent magnets can be artificially created, just as iron can be made temporarily magnetic. The ability to retain magnetism is called “remanence”. An example of a non permanent piece of metal that is often made magnetic is the tip of a screwdriver.

Magnetite:
fAHy4Io8KmRPgp8.jpg
Source: https://commons.wikimedia.org/w/index.php?curid=10139390 (2026-09-06)

Magnetic screwdriver:
A6h1WgVGQ9v4m7Q.jpg
Source: https://www.howtogeek.com/854142/is-it-safe-to-use-magnetic-screwdriver-in-a-pc/ (2026-09-26)

Magnets have two poles. In case of a bar magnet, they are called north/N-pole and south/S-pole. The magnetic flow emanates from the N-pole and returns through the S-pole. The magnetic flow is illustrated with field lines, which are imaginary, but a great way to start understanding magnetic fields and their directions. N-poles are often both illustrated and physically colored red, while S-poles are often white.

Bar magnet with illustrated field lines:
oBvBTlrGlICZnR0.jpg
Source: https://www.archyde.com/top-10-must-have-smartphones-right-now-galaxy-a56-xiaomi-15t-pro-more/ (2026-09-26)

Two materials of the same polarity can never be united and two materials of opposite polarity will attract each other with equal force.

zdhpvbfDtF6p74O.jpg
Source: https://stock.adobe.com/images/shows-a-diagram-of-magnetic-field-in-a-situation-of-repelling-and-attraction/112218437 (2026-09-06)

Magnetic fields can be manipulated or lead to flow in certain directions or in a more concentrated manner. For instance, by placing a bar magnet between the two ends of a U-shaped piece of iron.

(Illustration needed.)

To be continued. Meanwhile:

  1. I suppose “no magnetic phenomena occur outside the atom” is an oversimplification and what they really mean to say is that no magnetic fields are produced outside the atom?
  2. Do electrons really all rotate in the very same or the opposite three dimensional direction, or is this an oversimplification too and they really:

    • either rotate in a great variety of directions
    • or in similar directions
  3. By “united”, are they talking about nuclear fusion? I’m asking because I can physically push two N-poles together and make them touch if the magnet is small enough…

  4. It doesn’t sound or feel intuitive to say that opposite polarities will attract with equal force. What if one magnet has a mass of 20kg and the other 2 grams?
0

Electricity basics - Power

preview

We have come to understand - with the help of earlier posts - that voltage drives current and that this current can do useful work for us. The amount of work that voltage and current can do is expressed as “power”. The unit of power is watt/W, but when doing calculations “P” is used, taken from the first letter in the word “power”. If on an electric appliance you find the markings “230V, 40W”, it is to be understood that the appliance does useful work for us at the power of 40 watts if it is supplied the voltage 230 volts. If one does not supply the appliance with the prescribed voltage, it will not do useful work for us at the desired power.

Power is a product of voltage and current and can thus be calculated by voltage times current or V * I. The formulaic circle below summarizes both Ohm’s Law - as presented in an earlier post - and how to calculate power:

MYEiTlGtTSDlwhy.png
Source: https://ashlandacademicscience.miraheze.org/w/index.php?curid=209 (2026-09-04)

There is a great variety of electric appliances, for instance lightbulbs, heaters and motors, that do different kinds of useful work for us, for instance creating light, heat and motion.

Electric appliances:
gs1PKJux8DWlbet.jpg
Source: https://www.dreamstime.com/stock-illustration-home-electric-appliance-illustration-icon-set-hand-drawn-sketch-image92394788 (2026-09-04)

In these cases, power is reaped in desirable ways. However, power can also be wasted in undesirable ways! Before current reaches the intended load - the lightbulb, the heater or the motor - it needs to be transported to the load through the conductor(s). Regardless of how efficient a conductor we use, there will always be some resistance, as explained earlier, which in turn will make the voltage and the current to be translated into heat, which is seldom useful: there is a loss of power. The same amount of current will reach the load, but the voltage is diminished through the loss of power. This drop in voltage is referred to as a “voltage drop”.

The way to express how much energy is “used” during a certain period of time is given in “watt seconds/Ws” or “joules”. However, it is more common and useful to express it in “kilowatt hours/kWh”. For instance, a boiler that has a power output of 1000 watts and is used for 30 minutes will have used 1000 * 0,5 or 500 watt hours or 0,5 kilowatt hours.

To be continued: Meanwhile:

  1. This one was really hard to translate in my head. For instance, in Swedish the book litterally says “power is developed” instead of “power is generated”. Is it confusing to say this in English? Similarly, is “loss of power” or “power loss” the correct term to express how power is lost during transport? Also, the watts and voltages that are written on electric appliences are, in Swedish, called “marked power/marked voltage”. Are there equivalents in English?
  2. Is there any intuitive ways to visualize or imagine why current remains the same when a voltage drop occurs? If I understand correctly, current is expressed in ampere, which is a fixed amount of electrons passing through any one point in a circuit in one second. This current is driven by voltage. If resistance is constant, current increases when voltage is increased (I know nothing of the ratios). Wouldn’t a voltage drop mean that less electrons are pushed through that one point in the circuit in one second?

We have come to understand - with the help of earlier posts - that voltage drives current and that this current can do useful work for us. The amount of work that voltage and current can do is expressed as “power”. The unit of power is watt/W, but when doing calculations “P” is used, taken from the first letter in the word “power”. If on an electric appliance you find the markings “230V, 40W”, it is to be understood that the appliance does useful work for us at the power of 40 watts if it is supplied the voltage 230 volts. If one does not supply the appliance with the prescribed voltage, it will not do useful work for us at the desired power.

Power is a product of voltage and current and can thus be calculated by voltage times current or V * I. The formulaic circle below summarizes both Ohm’s Law - as presented in an earlier post - and how to calculate power:

MYEiTlGtTSDlwhy.png
Source: https://ashlandacademicscience.miraheze.org/w/index.php?curid=209 (2026-09-04)

There is a great variety of electric appliances, for instance lightbulbs, heaters and motors, that do different kinds of useful work for us, for instance creating light, heat and motion.

Electric appliances:
gs1PKJux8DWlbet.jpg
Source: https://www.dreamstime.com/stock-illustration-home-electric-appliance-illustration-icon-set-hand-drawn-sketch-image92394788 (2026-09-04)

In these cases, power is reaped in desirable ways. However, power can also be wasted in undesirable ways! Before current reaches the intended load - the lightbulb, the heater or the motor - it needs to be transported to the load through the conductor(s). Regardless of how efficient a conductor we use, there will always be some resistance, as explained earlier, which in turn will make the voltage and the current to be translated into heat, which is seldom useful: there is a loss of power. The same amount of current will reach the load, but the voltage is diminished through the loss of power. This drop in voltage is referred to as a “voltage drop”.

The way to express how much energy is “used” during a certain period of time is given in “watt seconds/Ws” or “joules”. However, it is more common and useful to express it in “kilowatt hours/kWh”. For instance, a boiler that has a power output of 1000 watts and is used for 30 minutes will have used 1000 * 0,5 or 500 watt hours or 0,5 kilowatt hours.

To be continued: Meanwhile:

  1. This one was really hard to translate in my head. For instance, in Swedish the book litterally says “power is developed” instead of “power is generated”. Is it confusing to say this in English? Similarly, is “loss of power” or “power loss” the correct term to express how power is lost during transport? Also, the watts and voltages that are written on electric appliences are, in Swedish, called “marked power/marked voltage”. Are there equivalents in English?
  2. Is there any intuitive ways to visualize or imagine why current remains the same when a voltage drop occurs? If I understand correctly, current is expressed in ampere, which is a fixed amount of electrons passing through any one point in a circuit in one second. This current is driven by voltage. If resistance is constant, current increases when voltage is increased (I know nothing of the ratios). Wouldn’t a voltage drop mean that less electrons are pushed through that one point in the circuit in one second?
0

Electricity basics - The relationship between voltage, current and resistance

preview

In the previous post, we were talking about creating light by leveraging the properties of electricity: voltage, current and resistance. Voltage occurs when two opposite charges consitute a potential difference in a closed circuit. This voltage in turn causes a current - a flow of electrons - in our circuit, flowing from the negative node of the power source to the positive node of the power source. When the current passes through the load of our circuit - a filament made of tungsten in our case with the lightbulb - it encounters high resistance. As current is forced through this high resistance, heat is generated. The increased heat increases the resistivity of the tungsten filament, and vice versa, which at a certain point starts emitting light.

Tungsten filament emitting light:
NmA5cm5sxczeElq.jpg
Source: https://www.azom.com/article.aspx?ArticleID=1538 (2026-09-02)

We can - to some extent - control how much light is emitted by increasing or decreasing the amount of current that flows through the filament. There are two methods for achieving this:

  1. Voltage causes current to flow, which means that if we increase the voltage - and the resistance stays constant - the current also increases, and vice versa.
  2. Resistance hinders the flow of current, which means that if we increase the resistance - and the voltage stays constant - the current decreases, and vice versa. There are - as we discussed earlier - at least three ways to manipulate resistance:
  • choose a material for our conductor/load with greater or lesser resistivity
  • change the length of the conductor/load
  • change the thickness of the conductor/load

To summarize, we can regulate current by changing voltage if resistance stays the same or by changing resistance if voltage stays the same. This relationship between these three characteristics of electricity is expressed and explained by Ohm’s Law. One takeaway from Ohm’s Law gives us a means to calculate any one of these three properties if two of them are known. This relationship can be represented with the following triangle, which also gives us what arithmetics should be performed on the properties and in what order to find the value of which property.

Ohm’s Law expressed with a triangle:
hCz9RiBGomq7DfL.png
Source: https://www.inchcalculator.com/ohms-law-calculator/ (2026-09-02)

A few notes:

  • Voltage/V is sometimes expressed as “E”, which is the first letter in “electromotive force”, which helps us visualize how voltage actually drives, “motivates” or gives “motion” to current. It can also be represented by “U”.
  • Current is represented by “I”, which comes from the French phrase intensité du courant (current intensity).

To be continued. Meanwhile:

  1. Where does the “U” come from? It seems to be an international standardization for symbolizing voltage.

In the previous post, we were talking about creating light by leveraging the properties of electricity: voltage, current and resistance. Voltage occurs when two opposite charges consitute a potential difference in a closed circuit. This voltage in turn causes a current - a flow of electrons - in our circuit, flowing from the negative node of the power source to the positive node of the power source. When the current passes through the load of our circuit - a filament made of tungsten in our case with the lightbulb - it encounters high resistance. As current is forced through this high resistance, heat is generated. The increased heat increases the resistivity of the tungsten filament, and vice versa, which at a certain point starts emitting light.

Tungsten filament emitting light:
NmA5cm5sxczeElq.jpg
Source: https://www.azom.com/article.aspx?ArticleID=1538 (2026-09-02)

We can - to some extent - control how much light is emitted by increasing or decreasing the amount of current that flows through the filament. There are two methods for achieving this:

  1. Voltage causes current to flow, which means that if we increase the voltage - and the resistance stays constant - the current also increases, and vice versa.
  2. Resistance hinders the flow of current, which means that if we increase the resistance - and the voltage stays constant - the current decreases, and vice versa. There are - as we discussed earlier - at least three ways to manipulate resistance:
  • choose a material for our conductor/load with greater or lesser resistivity
  • change the length of the conductor/load
  • change the thickness of the conductor/load

To summarize, we can regulate current by changing voltage if resistance stays the same or by changing resistance if voltage stays the same. This relationship between these three characteristics of electricity is expressed and explained by Ohm’s Law. One takeaway from Ohm’s Law gives us a means to calculate any one of these three properties if two of them are known. This relationship can be represented with the following triangle, which also gives us what arithmetics should be performed on the properties and in what order to find the value of which property.

Ohm’s Law expressed with a triangle:
hCz9RiBGomq7DfL.png
Source: https://www.inchcalculator.com/ohms-law-calculator/ (2026-09-02)

A few notes:

  • Voltage/V is sometimes expressed as “E”, which is the first letter in “electromotive force”, which helps us visualize how voltage actually drives, “motivates” or gives “motion” to current. It can also be represented by “U”.
  • Current is represented by “I”, which comes from the French phrase intensité du courant (current intensity).

To be continued. Meanwhile:

  1. Where does the “U” come from? It seems to be an international standardization for symbolizing voltage.
0

Electricity basics - The electric circuit

preview

We can harness electric charges and their potentials by artificially creating networks of paths for them in which they can equalize. We call these networks “circuits” and we can use them to create light, among other things.

This is a circuit:
ZTPu6hstSL6NT35.png
Source: https://www.caretxdigital.com/split-ac-outdoor-contactor-wiring-diagram-2/ (2026-09-02)

This is also a circuit:
jVjl88L9jrUzczn.webp
Source: https://stock.adobe.com/in/images/a-complex-electrical-wiring-diagram-with-colorful-wires-circuits-and-components-on-a-white-background-illustrating-a-detailed-schematic-for-an-electronic-system/938846171 (2026-09-02)

In the previous post, we saw how objects or materials can become negatively or positively charged by friction, such as when you - wearing slippers - walk over a carpet: electrons from the carpet are “smeared” onto you, making you negatively charged until you discharge/equalize your potential by touching something that is less negatively charged.

There are canisters/containers that hold opposite charges artificially: batteries. How nifty, that we can carry around canisters of electric potentinal in our pockets!!!

Various batteries:
a34BSuHXBBD1YWj.jpg
Source: https://www.popsci.com/technology/why-so-many-batteries/ (2026-09-02)

In simple terms, batteries contain two chambers with opposite charges, one negative and one positive. To access the charges inside the chambers, we add a gate to each chamber called nodes: one negative and one positive. If the two nodes are in some way connected to each other, a path is created for the charges in the chambers to equalize. That which connects the two nodes is called a “conductor” and it is the potential difference - the voltage - in the charges that drives the equalization. Where there is a potential difference, charges always want to equalize. Connecting two opposite charges this way is one way of creating an electric circuit. When the circuit is closed - when we connect the two opposite charges - a current of these charges in the form of electrons is allowed to flow through the conductor from the negative chamber to the positive chamber. The flow of electrons in a closed circuit, “carrying” charges, is called an electric current and it goes on until the potential difference has been equalized.

Electrons do not move with the speed of light. That which we perceive as an instantaneous effect of closing a circuit, for instance flicking a light switch, is the effect of the flow of electrons. When an electric circuit is closed, an electromagnetic wave propagates all over the circuit. This wave pushes the electrons in the direction of the potential difference - negative to positive - so that the electrons closest to the negative “source” pushes the electrons closest to the positive “end”. This propagation of the electromagnetic wave occurs almost at the speed of light. Saying that “electrons move at the speed of light” is just a simplification.

Open circuit:
jOnH8paEvLPgQgR.jpg
Source: Petzold, Charles. Code: The Hidden Language of Computer Hardware and Software: Second Edition. Pearson Education, Inc. 2023. p22.

Closed circtui:
JIsAbVxSxGRILGG.jpg
Source: ibid.

That which we used to connect the two nodes of the battery is usually made of copper, but different materials are differently good - or bad - at allowing electric current to flow. Electrons orbit the atomic nucleus at various distances, simplified as “shells”. The number of electrons that orbit an atom differs by what basic element that specific atom constitutes. Some elements - or materials - have electrons that are not strongly bound to shells. These materials have “free electrons” or “valence electrons”. Valence electrons in conductors move even when there is no voltage applied, but they move randomly and very slowly. By applying a voltage, we can influence the movement of the electrons.

Valence electrons:
x3PDsfrq0TbpW1f.webp
Source: https://valenceelectrons.com/valence-electrons-of-copper/ (2026-09-01)

Materials that have many valence electrons - often metals - are called conductors and materials that have no valence electrons - such as glass, plastic and ceramic - are called insulators. The ability of a material to allow current is called conductivity and its inability to allow current is called resistivity. One way to picture resistivity is to imagine electrons colliding with other particles, creating friction. High conductivity = low resistivity and vice versa. The resistivity of a material is decided by what material we are talking about, its temperature, length and thickness. Temperature plays a role because heat increases the random movement of electrons. Therefore, resistivity must be given alongside temperature. A short, thick, cool conductor has generally lower resistivity while a long, thin, hot conductor has generally higher resistivity.

Finally, returning to creating light, let’s add a lightbulb between the two nodes of the batteries as in the images above. The filament in traditional lightbulbs is a long, thin piece of material called tungsten, which endures high temperatures. Because the current in a closed circuit - the flow of electrons - continues with the same pressure (voltage) but encounters higher resistance in the filament, only a few electrons are going to be able to pass through it at any given time. The potential is going to equalize at a slower pace. The resistance that the flow of electrons encounters creates heat. Heat increases the resistivity of the filament. This circle continues until the lightbulb reaches its target temperature and emits light. A component in an electric circuit that does “useful work” this way, such as a lightbulb - or its filament - is called a “load”.

Tungsten filament, no current:
9LhnM1OZ3dRfz4I.png
Source: https://tdmfginc.net/product/tungsten-filament/ (2026-09-02)

Tungsten filament, with current:
QjaeVVYFMEVot00.jpg
Source: https://www.azom.com/article.aspx?ArticleID=1538 (2026-09-02)

If the circuit, intentionally or not, is closed before or after the load - in other words bypassing it - a short circuit occurs. Electric current always chooses the path with the least resistance. Because of the low resistance, a surge in current occurs, possibly depleting our batteries very quickly.

To be continued. Meanwhile:

  1. What is the difference between “resistivity” and “resistance”?
  2. “This circle continues until the lightbulb reaches its target temperature and emits light.” This must be an oversimplification for the highschoolers. Couldn’t you just keep increasing the voltage and reach even higher temperatures, even more light, until the filament pops/melts?
  3. I have never seen temperature written on any electric product. I might have seen resistance on a pair of headphones, but are there any common appliences in our everyday lives at all that also give at what temperature it works with what resistance?
  4. I’m confused about what the book says about the relationship between valence electrons and conductivity. Copper has one valence electron, right? Aren’t there metals that we could use that have more valence electrons and thus better conductivity? Or is copper wire just that much cheaper to produce?

We can harness electric charges and their potentials by artificially creating networks of paths for them in which they can equalize. We call these networks “circuits” and we can use them to create light, among other things.

This is a circuit:
ZTPu6hstSL6NT35.png
Source: https://www.caretxdigital.com/split-ac-outdoor-contactor-wiring-diagram-2/ (2026-09-02)

This is also a circuit:
jVjl88L9jrUzczn.webp
Source: https://stock.adobe.com/in/images/a-complex-electrical-wiring-diagram-with-colorful-wires-circuits-and-components-on-a-white-background-illustrating-a-detailed-schematic-for-an-electronic-system/938846171 (2026-09-02)

In the previous post, we saw how objects or materials can become negatively or positively charged by friction, such as when you - wearing slippers - walk over a carpet: electrons from the carpet are “smeared” onto you, making you negatively charged until you discharge/equalize your potential by touching something that is less negatively charged.

There are canisters/containers that hold opposite charges artificially: batteries. How nifty, that we can carry around canisters of electric potentinal in our pockets!!!

Various batteries:
a34BSuHXBBD1YWj.jpg
Source: https://www.popsci.com/technology/why-so-many-batteries/ (2026-09-02)

In simple terms, batteries contain two chambers with opposite charges, one negative and one positive. To access the charges inside the chambers, we add a gate to each chamber called nodes: one negative and one positive. If the two nodes are in some way connected to each other, a path is created for the charges in the chambers to equalize. That which connects the two nodes is called a “conductor” and it is the potential difference - the voltage - in the charges that drives the equalization. Where there is a potential difference, charges always want to equalize. Connecting two opposite charges this way is one way of creating an electric circuit. When the circuit is closed - when we connect the two opposite charges - a current of these charges in the form of electrons is allowed to flow through the conductor from the negative chamber to the positive chamber. The flow of electrons in a closed circuit, “carrying” charges, is called an electric current and it goes on until the potential difference has been equalized.

Electrons do not move with the speed of light. That which we perceive as an instantaneous effect of closing a circuit, for instance flicking a light switch, is the effect of the flow of electrons. When an electric circuit is closed, an electromagnetic wave propagates all over the circuit. This wave pushes the electrons in the direction of the potential difference - negative to positive - so that the electrons closest to the negative “source” pushes the electrons closest to the positive “end”. This propagation of the electromagnetic wave occurs almost at the speed of light. Saying that “electrons move at the speed of light” is just a simplification.

Open circuit:
jOnH8paEvLPgQgR.jpg
Source: Petzold, Charles. Code: The Hidden Language of Computer Hardware and Software: Second Edition. Pearson Education, Inc. 2023. p22.

Closed circtui:
JIsAbVxSxGRILGG.jpg
Source: ibid.

That which we used to connect the two nodes of the battery is usually made of copper, but different materials are differently good - or bad - at allowing electric current to flow. Electrons orbit the atomic nucleus at various distances, simplified as “shells”. The number of electrons that orbit an atom differs by what basic element that specific atom constitutes. Some elements - or materials - have electrons that are not strongly bound to shells. These materials have “free electrons” or “valence electrons”. Valence electrons in conductors move even when there is no voltage applied, but they move randomly and very slowly. By applying a voltage, we can influence the movement of the electrons.

Valence electrons:
x3PDsfrq0TbpW1f.webp
Source: https://valenceelectrons.com/valence-electrons-of-copper/ (2026-09-01)

Materials that have many valence electrons - often metals - are called conductors and materials that have no valence electrons - such as glass, plastic and ceramic - are called insulators. The ability of a material to allow current is called conductivity and its inability to allow current is called resistivity. One way to picture resistivity is to imagine electrons colliding with other particles, creating friction. High conductivity = low resistivity and vice versa. The resistivity of a material is decided by what material we are talking about, its temperature, length and thickness. Temperature plays a role because heat increases the random movement of electrons. Therefore, resistivity must be given alongside temperature. A short, thick, cool conductor has generally lower resistivity while a long, thin, hot conductor has generally higher resistivity.

Finally, returning to creating light, let’s add a lightbulb between the two nodes of the batteries as in the images above. The filament in traditional lightbulbs is a long, thin piece of material called tungsten, which endures high temperatures. Because the current in a closed circuit - the flow of electrons - continues with the same pressure (voltage) but encounters higher resistance in the filament, only a few electrons are going to be able to pass through it at any given time. The potential is going to equalize at a slower pace. The resistance that the flow of electrons encounters creates heat. Heat increases the resistivity of the filament. This circle continues until the lightbulb reaches its target temperature and emits light. A component in an electric circuit that does “useful work” this way, such as a lightbulb - or its filament - is called a “load”.

Tungsten filament, no current:
9LhnM1OZ3dRfz4I.png
Source: https://tdmfginc.net/product/tungsten-filament/ (2026-09-02)

Tungsten filament, with current:
QjaeVVYFMEVot00.jpg
Source: https://www.azom.com/article.aspx?ArticleID=1538 (2026-09-02)

If the circuit, intentionally or not, is closed before or after the load - in other words bypassing it - a short circuit occurs. Electric current always chooses the path with the least resistance. Because of the low resistance, a surge in current occurs, possibly depleting our batteries very quickly.

To be continued. Meanwhile:

  1. What is the difference between “resistivity” and “resistance”?
  2. “This circle continues until the lightbulb reaches its target temperature and emits light.” This must be an oversimplification for the highschoolers. Couldn’t you just keep increasing the voltage and reach even higher temperatures, even more light, until the filament pops/melts?
  3. I have never seen temperature written on any electric product. I might have seen resistance on a pair of headphones, but are there any common appliences in our everyday lives at all that also give at what temperature it works with what resistance?
  4. I’m confused about what the book says about the relationship between valence electrons and conductivity. Copper has one valence electron, right? Aren’t there metals that we could use that have more valence electrons and thus better conductivity? Or is copper wire just that much cheaper to produce?
0

Electricity basics - Electric equilibrium

preview

The core, the nucleus, of an atom consists of positively charged protons and of neutrons that do not have any charge. The nucleus in its entirety is considered to be positively charged. Surrounding the atomic nucleus is a cloud of electrons. Electrons are negatively charged. If the number of electrons are the same as the number of protons, then the atom is electrically neutral. There is electric equilibrium.

C2FyELcFNEiB3zc.jpg
Source: https://www.sciencefacts.net/atom-2.html (2026-08-31)

This equilibrium can change. This happens when the number of electrons is unequal to the number of protons. The atom is then called an ion. If there are more electrons than protons, the ion is negatively charged. If there are less electrons than protons, the ion is positively charged.

AfLAuzrLwBINjCs.png
Source: https://sciencenotes.org/what-is-the-difference-between-an-atom-and-an-ion/ (2026-08-31)

Any object or material that contains ions is no longer electrically neutral. It has an electric charge or “potential”. Between to differently charged objects or materia, there is potential difference or “voltage”. This electric imbalance always wants to equalize: atoms “want to be” neutral. Ions are either going to give away or receive the amount of electrons needed to achieve this equilibrium. This happens when two differently charged objects or materia directly touch or it can happen by influence in an electric field. Until a charge is equalized it remains and is considered static.

An example of charges equalizing by direct contact is when two differently charged people touch each other and experience a shock. Or when you happen to have collected an abundance of electrons, thus creating negative ions, and then you touch a differently charged object. Ouch (sometimes).

j3lxxyuULWD4OqP.webp
Source: https://thors.com/manufacturing-courses/manufactured-products/electrical-and-electronics/electrostatic-discharge-esd-basics/ (2026-08-31)

An example of charges equalizing through electric fields is lightning striking the ground. The potential difference between clouds and the ground grows so big that matter between them is ionized and finally, when the potentinal difference is big enough, the charges equalize in the form of visible current - lightning ⚡.

V3pPHL4zmzbFJoK.png
Source: https://www.savemyexams.com/igcse/physics/oxford-aqa/16/revision-notes/electricity-and-magnetism/electrical-circuits/static-electricity/ (2026-08-31)

Another example is dust particles pulled towards oppositely charged electric devices in your home. Or styrofoam on a cat.

dXhOKZHzGMSKNVZ.jpg
Source: https://commons.wikimedia.org/w/index.php?curid=60287175 (2026-08-31)

To be continued. Meanwhile, some questions that popped up:

  1. What determines the amount of voltage needed for a current to discharge in a scenario where the opposite charges never touch but only ever interact through the electric field? Some assumptions of mine: distance to each other, (air) humidity, medium (air, vacuum, other), resistance, interference from other electromagnetic waves…?
  2. What creates ions, except for the above mentioned physical friction? What natural phenomenon or scenarios kick electrons off or shoves them onto atoms? Is this what we artificially do in batteries? Creating negative and positive ions to create voltage?

The core, the nucleus, of an atom consists of positively charged protons and of neutrons that do not have any charge. The nucleus in its entirety is considered to be positively charged. Surrounding the atomic nucleus is a cloud of electrons. Electrons are negatively charged. If the number of electrons are the same as the number of protons, then the atom is electrically neutral. There is electric equilibrium.

C2FyELcFNEiB3zc.jpg
Source: https://www.sciencefacts.net/atom-2.html (2026-08-31)

This equilibrium can change. This happens when the number of electrons is unequal to the number of protons. The atom is then called an ion. If there are more electrons than protons, the ion is negatively charged. If there are less electrons than protons, the ion is positively charged.

AfLAuzrLwBINjCs.png
Source: https://sciencenotes.org/what-is-the-difference-between-an-atom-and-an-ion/ (2026-08-31)

Any object or material that contains ions is no longer electrically neutral. It has an electric charge or “potential”. Between to differently charged objects or materia, there is potential difference or “voltage”. This electric imbalance always wants to equalize: atoms “want to be” neutral. Ions are either going to give away or receive the amount of electrons needed to achieve this equilibrium. This happens when two differently charged objects or materia directly touch or it can happen by influence in an electric field. Until a charge is equalized it remains and is considered static.

An example of charges equalizing by direct contact is when two differently charged people touch each other and experience a shock. Or when you happen to have collected an abundance of electrons, thus creating negative ions, and then you touch a differently charged object. Ouch (sometimes).

j3lxxyuULWD4OqP.webp
Source: https://thors.com/manufacturing-courses/manufactured-products/electrical-and-electronics/electrostatic-discharge-esd-basics/ (2026-08-31)

An example of charges equalizing through electric fields is lightning striking the ground. The potential difference between clouds and the ground grows so big that matter between them is ionized and finally, when the potentinal difference is big enough, the charges equalize in the form of visible current - lightning ⚡.

V3pPHL4zmzbFJoK.png
Source: https://www.savemyexams.com/igcse/physics/oxford-aqa/16/revision-notes/electricity-and-magnetism/electrical-circuits/static-electricity/ (2026-08-31)

Another example is dust particles pulled towards oppositely charged electric devices in your home. Or styrofoam on a cat.

dXhOKZHzGMSKNVZ.jpg
Source: https://commons.wikimedia.org/w/index.php?curid=60287175 (2026-08-31)

To be continued. Meanwhile, some questions that popped up:

  1. What determines the amount of voltage needed for a current to discharge in a scenario where the opposite charges never touch but only ever interact through the electric field? Some assumptions of mine: distance to each other, (air) humidity, medium (air, vacuum, other), resistance, interference from other electromagnetic waves…?
  2. What creates ions, except for the above mentioned physical friction? What natural phenomenon or scenarios kick electrons off or shoves them onto atoms? Is this what we artificially do in batteries? Creating negative and positive ions to create voltage?