0

CEL on pickup for an oil change, not sure what to think

preview

2019 VW petrol Golf R w/39K miles

CEL = Check Engine Light

tl;dr Started with a car with no CEL. After oil change, CEL. Another shop discovers it is due to an electrical connection to a part of my turbo assembly not being securely plugged in. Do I tell the garage owners?

Prior to drop off no CEL, ~3 hours later, after they have closed, I turn on the car and immediately get a CEL.

Verified I didn’t have a lake of expensive oil under my car and the oil was in fact in the engine. My road side emergency bargain basement odb2 reader wasn’t showing any codes and trying to clear/reset did nothing.

Garage responded the next morning and explains they forgot to clear something in the VW computer and its just a 2 second fix. Unfortunately I am gone for the next month. The car is parked the entire time and no one drives it.

Month and change later, I finally get home, get the car to the garage, and they say “Oh actually it’s P033, your waste gate actuator.” As someone who has owned more than one VW, I am unfortunately familiar with that code. Except this car only has 39K miles and those are NOT redlining on the track miles.

So I take my car to another garage and repeat verbatim the above. I told them to treat this like a crime scene and take their time. Five minutes into the diagnostics check they discovered the electrical connector to the DV (diverter valve, basically the uncool ninja alternative to a blow off valve) wasn’t properly/completely plugged in. After reseating that connector the CEL didn’t come back. I never felt any turbo lag nor heard or felt anything to suggest the DV wasn’t working, I am guessing the connector was just loose enough to freak out the ECM.

This is the problem. I have used that first garage for over 10 years and got on well with the owners. Unfortunately a new guy to the company is the only person who touched the car from oil change onward. I’ve gone over my maintenance records and I just don’t see why anyone was messing with the DV or anything over there on my engine bay in over two years. Also I have a hard time imagining the connector magically jiggling loose in the hour or so after the new guy parked it outside for pickup.

I don’t have the energy to scooby doo this shit and piss the ECM off so it throws the same code and then take it to them to see what they would do. So I will never know.

Do I tell the garage owners? I don’t see how there is anyway to make this right that I am comfortable trusting them with my car.

What would you do?

2019 VW petrol Golf R w/39K miles

CEL = Check Engine Light

tl;dr Started with a car with no CEL. After oil change, CEL. Another shop discovers it is due to an electrical connection to a part of my turbo assembly not being securely plugged in. Do I tell the garage owners?

Prior to drop off no CEL, ~3 hours later, after they have closed, I turn on the car and immediately get a CEL.

Verified I didn’t have a lake of expensive oil under my car and the oil was in fact in the engine. My road side emergency bargain basement odb2 reader wasn’t showing any codes and trying to clear/reset did nothing.

Garage responded the next morning and explains they forgot to clear something in the VW computer and its just a 2 second fix. Unfortunately I am gone for the next month. The car is parked the entire time and no one drives it.

Month and change later, I finally get home, get the car to the garage, and they say “Oh actually it’s P033, your waste gate actuator.” As someone who has owned more than one VW, I am unfortunately familiar with that code. Except this car only has 39K miles and those are NOT redlining on the track miles.

So I take my car to another garage and repeat verbatim the above. I told them to treat this like a crime scene and take their time. Five minutes into the diagnostics check they discovered the electrical connector to the DV (diverter valve, basically the uncool ninja alternative to a blow off valve) wasn’t properly/completely plugged in. After reseating that connector the CEL didn’t come back. I never felt any turbo lag nor heard or felt anything to suggest the DV wasn’t working, I am guessing the connector was just loose enough to freak out the ECM.

This is the problem. I have used that first garage for over 10 years and got on well with the owners. Unfortunately a new guy to the company is the only person who touched the car from oil change onward. I’ve gone over my maintenance records and I just don’t see why anyone was messing with the DV or anything over there on my engine bay in over two years. Also I have a hard time imagining the connector magically jiggling loose in the hour or so after the new guy parked it outside for pickup.

I don’t have the energy to scooby doo this shit and piss the ECM off so it throws the same code and then take it to them to see what they would do. So I will never know.

Do I tell the garage owners? I don’t see how there is anyway to make this right that I am comfortable trusting them with my car.

What would you do?

0

Are HEPA cabin air filters unsafe for some vehicles?

preview

Yes, I’m aware that companies sell HEPA cabin air filters for vehicles. But, is it safe to install a HEPA cabin air filter on a vehicle who’s HVAC system wasn’t designed for HEPA air filters?

engineersedge.com/…/hepa_filter_pressure_drop_con…

By design, HEPA air filters will create resistance to flow, and a high differential pressure drop will exist across the filter. Most HEPA air filter manufacturers literature suggests replacement of HEPA air filters when the resistance due to dust loading has reached 2 in.wg.

So if your car’s HVAC is designed for high airflow and you slap a HEPA filter on it, are you adding more stress and wear on the system? Seems like it’s the exact same problem of installing an overly restrictive filter on your home’s HVAC return vent.

Yes, I’m aware that companies sell HEPA cabin air filters for vehicles. But, is it safe to install a HEPA cabin air filter on a vehicle who’s HVAC system wasn’t designed for HEPA air filters?

engineersedge.com/…/hepa_filter_pressure_drop_con…

By design, HEPA air filters will create resistance to flow, and a high differential pressure drop will exist across the filter. Most HEPA air filter manufacturers literature suggests replacement of HEPA air filters when the resistance due to dust loading has reached 2 in.wg.

So if your car’s HVAC is designed for high airflow and you slap a HEPA filter on it, are you adding more stress and wear on the system? Seems like it’s the exact same problem of installing an overly restrictive filter on your home’s HVAC return vent.

0

2017 Polaris sportsman 450 whining sound in the motor after oil change

preview

Title sums it up. The 4-wheeler at the non-profit I’m affiliated with hadn’t had an oil change in at least 2 years, they use it frequently. We’d really like an affordable option that I can do to fix.

Sound is new after changing the oil (with official Polaris kit specifically for the vehicle). Instructions from Polaris were followed exactly.

I’ve uploaded a video that hopefully makes the sound audible. It seems to me to be coming more from the cylinder area than anywhere else. I have another video here showing that the sound increases with engine speed, and it’s obnoxiously loud.

Please let me know if there are any additional details I can provide.

Everyone involved is fully aware that at least 2 years is too damn long, so if we can skip any admonishments, that would be appreciated.

Title sums it up. The 4-wheeler at the non-profit I’m affiliated with hadn’t had an oil change in at least 2 years, they use it frequently. We’d really like an affordable option that I can do to fix.

Sound is new after changing the oil (with official Polaris kit specifically for the vehicle). Instructions from Polaris were followed exactly.

I’ve uploaded a video that hopefully makes the sound audible. It seems to me to be coming more from the cylinder area than anywhere else. I have another video here showing that the sound increases with engine speed, and it’s obnoxiously loud.

Please let me know if there are any additional details I can provide.

Everyone involved is fully aware that at least 2 years is too damn long, so if we can skip any admonishments, that would be appreciated.

0

[solved] Right blinker issue - Citroen C3 II (~2012)

preview

This post is an update from this one: link

Hi,

I have a right blinker problem on my car, specifically the right side repeater and rear right indicators.

They used to work on and off sporadically but now they don’t work anymore.

When they break, they both break at the same time.

Disclaimer, I am a beginner who watches youtube videos and search stuff online. So far I have changed a radio and a diesel return line on another car.

Pictures (sorry for the resolution)

Here’s a schematic I found online for my car model:

Here’s another:

Both found here: https://www.c3manuel.com/indicateurs_de_direction_signal_danger-106.html

And here’s a simplified one made by myself:

Findings

  • Lamp module 2635 (rear right): OK

  • Connector and pins 2635: OK

  • Lamp module 2345 (right side repeater): OK

  • Wiring [BSI - PH1 - #13] -> [2635]: OK (I even replaced it, ruining a perfectly good original part >.<)

  • Wiring [BSI - EP - #19] -> [2345]: Untested, very hard to reach

  • Ground MC70: OK (because the other lights (stop and fog) are working fine)

  • Ground MC20: OK (because the front right blinker goes there and this one’s working)

  • Front right blinker: OK

  • Left blinkers: OK

  • Blinker fluid: OK ^^

  • The BSI isn’t sending a pulsing 12V to PH1#13 and EP#19.

  • The ticking is faster on the right side.

What can I check/do next? I am kinda lost.

As I said before, I am a beginner so every piece of advice is welcome.

Solved

BSI was replaced and it works now

This post is an update from this one: link

Hi,

I have a right blinker problem on my car, specifically the right side repeater and rear right indicators.

They used to work on and off sporadically but now they don’t work anymore.

When they break, they both break at the same time.

Disclaimer, I am a beginner who watches youtube videos and search stuff online. So far I have changed a radio and a diesel return line on another car.

Pictures (sorry for the resolution)

Here’s a schematic I found online for my car model:

Here’s another:

Both found here: https://www.c3manuel.com/indicateurs_de_direction_signal_danger-106.html

And here’s a simplified one made by myself:

Findings

  • Lamp module 2635 (rear right): OK

  • Connector and pins 2635: OK

  • Lamp module 2345 (right side repeater): OK

  • Wiring [BSI - PH1 - #13] -> [2635]: OK (I even replaced it, ruining a perfectly good original part >.<)

  • Wiring [BSI - EP - #19] -> [2345]: Untested, very hard to reach

  • Ground MC70: OK (because the other lights (stop and fog) are working fine)

  • Ground MC20: OK (because the front right blinker goes there and this one’s working)

  • Front right blinker: OK

  • Left blinkers: OK

  • Blinker fluid: OK ^^

  • The BSI isn’t sending a pulsing 12V to PH1#13 and EP#19.

  • The ticking is faster on the right side.

What can I check/do next? I am kinda lost.

As I said before, I am a beginner so every piece of advice is welcome.

Solved

BSI was replaced and it works now

0

Ford O2 sensors, same or different?

preview

I noticed on the 2001 expedition I bought that it looks like they put an O2 sensor with the long cord before the cat. All the ones online say the long cord is the back one.

There is conflicting info online. Does it matter, are all o2 sensors the same? Before cat, after cat doesn’t matter?

I noticed on the 2001 expedition I bought that it looks like they put an O2 sensor with the long cord before the cat. All the ones online say the long cord is the back one.

There is conflicting info online. Does it matter, are all o2 sensors the same? Before cat, after cat doesn’t matter?

0

Does this look factory or handmade? Should I avoid tinkering?

preview

UPDATE:https://lemmy.world/post/50623501

Trying to figure out where I am losing voltage for rear right blinker on a C3 II.

Connectors on the light module are OK, I tried on the left side, compared with a multimeter and I should get a pulsing Voltage (12V if I recall) but the gray one stays at 0 on the right side.

So I followed the wire all the way to under the glove box where I found what looks like a burned resistor.

Edit: it’s a plastic shielding:

I’m pretty new to this so if I’m looking at the wrong things please feel free to tell.

UPDATE:https://lemmy.world/post/50623501

Trying to figure out where I am losing voltage for rear right blinker on a C3 II.

Connectors on the light module are OK, I tried on the left side, compared with a multimeter and I should get a pulsing Voltage (12V if I recall) but the gray one stays at 0 on the right side.

So I followed the wire all the way to under the glove box where I found what looks like a burned resistor.

Edit: it’s a plastic shielding:

I’m pretty new to this so if I’m looking at the wrong things please feel free to tell.

0

2001 Infiniti QX4/Nissan Pathfinder - what is this noise?

preview

Sounds like gears rubbing or something. Maybe a chain or belt? Sounds like it’s coming from the front of the engine and it goes up and down in pitch with throttle.

For context, I recently got some water in the intake, but not enough to hydrolock. Changed MAF. Idles fine.

Thanks!

EDIT: I think the sound is coming from one of the belt pulleys. Upper left one?

Edit edit: I’m pretty sure it’s the alternator now. Will follow up.

Sounds like gears rubbing or something. Maybe a chain or belt? Sounds like it’s coming from the front of the engine and it goes up and down in pitch with throttle.

For context, I recently got some water in the intake, but not enough to hydrolock. Changed MAF. Idles fine.

Thanks!

EDIT: I think the sound is coming from one of the belt pulleys. Upper left one?

Edit edit: I’m pretty sure it’s the alternator now. Will follow up.

0

I cannot get this battery current sensor off of mu 2018 nissan altima, code p1550

preview

My car does not always start, and the code says this was the issue. The connection to the battery is pristine and silver AF. So I wanted to take this thing off and look at the connections to see if it needed to be replaced or if there is another issue.

But I can’t look for corrosion or replace it if I cannot get it off.

The things seem fused together. And I do not know what to do to safely get them separated.

My car does not always start, and the code says this was the issue. The connection to the battery is pristine and silver AF. So I wanted to take this thing off and look at the connections to see if it needed to be replaced or if there is another issue.

But I can’t look for corrosion or replace it if I cannot get it off.

The things seem fused together. And I do not know what to do to safely get them separated.

0

Warranty question

preview

I bought a used Forester, from a mechanic shop with a verbal warranty for 2 years. Covers engine and transmission. Transmission has to be replaced, and I’m being told it’s not covered.

He initially thought it was something attached (not sure what) and that leaks weren’t covered. But now that he’s dropped the transmission, he’s saying it’s leaking out of I think a crack in the transmission case. And since the internal parts didn’t break warranty doesn’t apply.

Am I being fucked over? I don’t see how the entire transmission replacement isn’t covered under a transmission warranty. USA

I bought a used Forester, from a mechanic shop with a verbal warranty for 2 years. Covers engine and transmission. Transmission has to be replaced, and I’m being told it’s not covered.

He initially thought it was something attached (not sure what) and that leaks weren’t covered. But now that he’s dropped the transmission, he’s saying it’s leaking out of I think a crack in the transmission case. And since the internal parts didn’t break warranty doesn’t apply.

Am I being fucked over? I don’t see how the entire transmission replacement isn’t covered under a transmission warranty. USA

0

Should I be concerned about the coloration of these spark plugs?

preview

Bought this car second hand, they apparently put iridium spark plugs in, but i want to know if I should be concerned with the buildup and rusty appearance it’s developed. For all I know this spark plug could be from 10 years ago.

Do I need to replace the plugs, and is that actually rust? Does this mean I have an issue with my head gasket?

Edit: Thanks guys! I’ll be ordering some new plugs soon.

Bought this car second hand, they apparently put iridium spark plugs in, but i want to know if I should be concerned with the buildup and rusty appearance it’s developed. For all I know this spark plug could be from 10 years ago.

Do I need to replace the plugs, and is that actually rust? Does this mean I have an issue with my head gasket?

Edit: Thanks guys! I’ll be ordering some new plugs soon.

0

Changeover valve broken - quick fix

preview

This broke on the drive home today (2000 Sprinter 208) and dumped all the water out of the system.

I bypassed it with an old sparkplug socket I had. This now means the heater core is always getting water circulating through it.

Does this matter? I live in a hot country so I never have the cabin heater on so it’s not like I’m missing out on owt…

This broke on the drive home today (2000 Sprinter 208) and dumped all the water out of the system.

I bypassed it with an old sparkplug socket I had. This now means the heater core is always getting water circulating through it.

Does this matter? I live in a hot country so I never have the cabin heater on so it’s not like I’m missing out on owt…

0

2009 Corolla 1.8L rough start and shudder

preview

Hey all, my wife’s 2009 Corolla has been taking a few turns to start. There’s misfires in every cylinder, and the engine shudders.

It was running fine when we got it around a year ago, and the problem slowly came about. I’ve replaced every ignition coil and spark plug, and they’re all firing fine. Then I thought it was oil getting into the spark plug wells, so I attached a straw to a shop vac and stuck it in each one (not much came out), then replaced the valve cover gasket.

It seems to be a fuel issue, but my fuel pump seems fine. I was thinking maybe it’s sensors, but I’m really lost and I have got to keep this vehicle running! Any advice would be welcome.

Hey all, my wife’s 2009 Corolla has been taking a few turns to start. There’s misfires in every cylinder, and the engine shudders.

It was running fine when we got it around a year ago, and the problem slowly came about. I’ve replaced every ignition coil and spark plug, and they’re all firing fine. Then I thought it was oil getting into the spark plug wells, so I attached a straw to a shop vac and stuck it in each one (not much came out), then replaced the valve cover gasket.

It seems to be a fuel issue, but my fuel pump seems fine. I was thinking maybe it’s sensors, but I’m really lost and I have got to keep this vehicle running! Any advice would be welcome.

0

Dash cam suggestion?

preview

I just got my first car and I was thinking I should probably get a dash cam since it has to stay in the driveway, but I feel out of my depth. I don’t have a lot of money so I’m hoping for one that is at most around AU$100. I also think covering both front and rear would be best, but obviously will take advice on that regard. Are there any specific ones you would recommend? I feel completely out of my depth. Also, I’m located in Australia if that makes a difference.

I just got my first car and I was thinking I should probably get a dash cam since it has to stay in the driveway, but I feel out of my depth. I don’t have a lot of money so I’m hoping for one that is at most around AU$100. I also think covering both front and rear would be best, but obviously will take advice on that regard. Are there any specific ones you would recommend? I feel completely out of my depth. Also, I’m located in Australia if that makes a difference.

0

Any VW people here?

preview

2019 VW Atlas SEL

Alignment has been off since I bought the car used. Dealership had to replace the steering rack for something unrelated and I told them to make sure the alignment is right. It was not. Maybe in their machine it is, but the wheel was not centered when driving straight. I looked at the live data in OBDEleven and there was an offset for mechanical center and straight line (see screenshots).

I adjusted the tie rods of each wheel equally so it would drive straight when steering wheel centered and ran the steering angle sensor basic setting in OBDEleven. I now notice that the dynamic lane assist (the alternate setting to stay in middle of lane) always veers to the right first and then centers. Also, the sensor offset is still there.

Is there something else I need to do to get rid of the offset? Something with ABS control unit?

EDIT: some additional live data

2019 VW Atlas SEL

Alignment has been off since I bought the car used. Dealership had to replace the steering rack for something unrelated and I told them to make sure the alignment is right. It was not. Maybe in their machine it is, but the wheel was not centered when driving straight. I looked at the live data in OBDEleven and there was an offset for mechanical center and straight line (see screenshots).

I adjusted the tie rods of each wheel equally so it would drive straight when steering wheel centered and ran the steering angle sensor basic setting in OBDEleven. I now notice that the dynamic lane assist (the alternate setting to stay in middle of lane) always veers to the right first and then centers. Also, the sensor offset is still there.

Is there something else I need to do to get rid of the offset? Something with ABS control unit?

EDIT: some additional live data

0

90's EGR Systems

preview

Anybody know anything about 90’s vacuum controlled EGR systems? I’ve got one of those goofy little Japanese import trucks, and finding info about how it’s supposed to work is a nightmare.

There’s a pretty good vacuum leak out of the top of the vacuum amplifier/signal doodad. Kinda UFO shaped deal between the vacuum advance, intake manifold and the canister.

Any ideas on diagnosis, or ways I can figure out what’s doing what would be helpful.

Anybody know anything about 90’s vacuum controlled EGR systems? I’ve got one of those goofy little Japanese import trucks, and finding info about how it’s supposed to work is a nightmare.

There’s a pretty good vacuum leak out of the top of the vacuum amplifier/signal doodad. Kinda UFO shaped deal between the vacuum advance, intake manifold and the canister.

Any ideas on diagnosis, or ways I can figure out what’s doing what would be helpful.

0

Honda Civic 2017 - Every Possible Warning Light On

preview

Hiya It happened recently that when I turn on the ignition all the electronic systems warning lights goes off. LKAS, ABS, ACC, VS, EP etc but the car runs all right apart from the obvious - the electronic support systems not working. The errors stay on during the driving.

I surmised that its not each individual system failed on its own, it must some sort bad connection maybe?

I already checked the battery (ignition off, switching on and idling) and is perfectly healthy.

I tried unplugging the battery for about 30min - didn’t do a thing.

I’m getting an OBD scanner tomorrow so i will post here what it comes back with.

In the meantime - any ideas?

Thank you!

Hiya It happened recently that when I turn on the ignition all the electronic systems warning lights goes off. LKAS, ABS, ACC, VS, EP etc but the car runs all right apart from the obvious - the electronic support systems not working. The errors stay on during the driving.

I surmised that its not each individual system failed on its own, it must some sort bad connection maybe?

I already checked the battery (ignition off, switching on and idling) and is perfectly healthy.

I tried unplugging the battery for about 30min - didn’t do a thing.

I’m getting an OBD scanner tomorrow so i will post here what it comes back with.

In the meantime - any ideas?

Thank you!

0

2006 Ford Escape 3.0L V6 Ignition Coil Replacement

preview

Hello mechanics!

I’ve got some coils and spark plugs that need replacing (Along with likely needing to send my ECM in for a repair). I’ve verified that they’re the likely culprit of many of my issues with my local mechanic, but wanted to verify with more internet experts on what to buy.

From what I understand, Motorcraft is the recommended OEM, and I’ve no problem spending the money if that is the right direction, but I wanted to see if any of these “Premium” alternatives on RockAuto would be a good or better choice, such as the Hitachi with “Magnetic Shield for EMI Protection” (A common cause for ECM damage in this make/model apparently).

Thanks in advance!

RockAuto

Hello mechanics!

I’ve got some coils and spark plugs that need replacing (Along with likely needing to send my ECM in for a repair). I’ve verified that they’re the likely culprit of many of my issues with my local mechanic, but wanted to verify with more internet experts on what to buy.

From what I understand, Motorcraft is the recommended OEM, and I’ve no problem spending the money if that is the right direction, but I wanted to see if any of these “Premium” alternatives on RockAuto would be a good or better choice, such as the Hitachi with “Magnetic Shield for EMI Protection” (A common cause for ECM damage in this make/model apparently).

Thanks in advance!

RockAuto

0

CVT lifespan

preview

Hi everyone,

I have a 2012 Nissan versa which uses a CVT. I am close to hitting 100k miles and just had my transmission serviced. I’m not having any problems with the transmission, but just wanted to do routine maintenance on my car. When I was at the shop, the guy kept telling me how unreliable CVTs are and I’m lucky I got 100k miles out of it. He also made it sound like it could totally fail at any point in the near future. So I’m just curious how long do CVTs last? He said they typically fail around 70k miles. If they truly don’t last much longer than 100k miles then maybe I should look into getting a new car while mine is still working. I tried looking it up online but I don’t trust the AI content.

Thanks!

Hi everyone,

I have a 2012 Nissan versa which uses a CVT. I am close to hitting 100k miles and just had my transmission serviced. I’m not having any problems with the transmission, but just wanted to do routine maintenance on my car. When I was at the shop, the guy kept telling me how unreliable CVTs are and I’m lucky I got 100k miles out of it. He also made it sound like it could totally fail at any point in the near future. So I’m just curious how long do CVTs last? He said they typically fail around 70k miles. If they truly don’t last much longer than 100k miles then maybe I should look into getting a new car while mine is still working. I tried looking it up online but I don’t trust the AI content.

Thanks!

0

2005 Hyundai Tucson 2.7L - Random acceleration issues and hesitation

preview

This thing has been driving us nuts! We’re slowly but systematically replacing basically every relevant part suggested by the various codes it’s thrown over the past few years, but it still acts up, totally randomly.

So far, we’ve replaced all the plugs, plug wires, coil packs, fuel pump, and crankshaft position sensor. I also briefly replaced the throttle position sensor, to which I didn’t notice any difference either, but my roommate (the owner) thought that seemed to somehow make it worse so he had me put the old one back in. We do still have the new one though, and after what it did yesterday, I might put the new one back in soon. More on what it did yesterday a little later.

Still on the menu of other parts to check/replace are the mass airflow sensor, oxygen sensor, EGR valve, and camshaft position sensor (this model does have that sensor right?)

Anyways, what it did yesterday threw us both for a loop. While parked at the gas station and idling, he pressed the accelerator pedal, and literally nothing happened, engine RPM didn’t change a single bit, even when he put the pedal to the floor it simply stayed at idle.

I wondered what the hell the computer was even thinking at that moment, like did the ECM just totally glitch out then or what? So I had him shut it down, wait about 20 seconds or so, and crank it back up. And sure enough it started responding to the accelerator again, as it has been for the past few years anyways.

I’m sure that it’s at least partly related to the emissions control system, as the exhaust definitely smells like it’s not burning all the gas (note that there’s thankfully no visible emissions, just a notable odor), but why the hell would there be a random one-off where the vehicle wouldn’t even respond to the accelerator at all until shutting it down and restarting it?

We’d go ahead and jump all in and replace all the other parts I mentioned, but ya know … $$$ … so we’re tackling things as he can afford them and as we narrow down and correct obvious issues such as a few cracked vacuum lines that I’ve already replaced now.

Anyways, if you’ve read this far, thanks for your attention to this issue. If anyone has any suggestions or advice to help us find the issue and save our sanity, we’re all ears! And thanks in advance.

Also, a bonus link for fellow mechanics: charm.li

Operation CHARM - The Collection of High-quality Auto Repair Manuals spans many makes and models from 1982 through 2013

This thing has been driving us nuts! We’re slowly but systematically replacing basically every relevant part suggested by the various codes it’s thrown over the past few years, but it still acts up, totally randomly.

So far, we’ve replaced all the plugs, plug wires, coil packs, fuel pump, and crankshaft position sensor. I also briefly replaced the throttle position sensor, to which I didn’t notice any difference either, but my roommate (the owner) thought that seemed to somehow make it worse so he had me put the old one back in. We do still have the new one though, and after what it did yesterday, I might put the new one back in soon. More on what it did yesterday a little later.

Still on the menu of other parts to check/replace are the mass airflow sensor, oxygen sensor, EGR valve, and camshaft position sensor (this model does have that sensor right?)

Anyways, what it did yesterday threw us both for a loop. While parked at the gas station and idling, he pressed the accelerator pedal, and literally nothing happened, engine RPM didn’t change a single bit, even when he put the pedal to the floor it simply stayed at idle.

I wondered what the hell the computer was even thinking at that moment, like did the ECM just totally glitch out then or what? So I had him shut it down, wait about 20 seconds or so, and crank it back up. And sure enough it started responding to the accelerator again, as it has been for the past few years anyways.

I’m sure that it’s at least partly related to the emissions control system, as the exhaust definitely smells like it’s not burning all the gas (note that there’s thankfully no visible emissions, just a notable odor), but why the hell would there be a random one-off where the vehicle wouldn’t even respond to the accelerator at all until shutting it down and restarting it?

We’d go ahead and jump all in and replace all the other parts I mentioned, but ya know … $$$ … so we’re tackling things as he can afford them and as we narrow down and correct obvious issues such as a few cracked vacuum lines that I’ve already replaced now.

Anyways, if you’ve read this far, thanks for your attention to this issue. If anyone has any suggestions or advice to help us find the issue and save our sanity, we’re all ears! And thanks in advance.

Also, a bonus link for fellow mechanics: charm.li

Operation CHARM - The Collection of High-quality Auto Repair Manuals spans many makes and models from 1982 through 2013

0

[Updated] Hydraulic lifters ticking in '95 Mazda 626

Proton Drive drive.proton.me
preview

It’s a 4-cyl I4 petrol engine ('95 Mazda 626) with a ticking noise that matches with revs. I’ve had it for a while and it seems to be getting louder as time goes on. It doesn’t go away even after longer drives.

The workshop I’ve used previously haven’t highlighted it when I had the car in for an inspection, but after a recent incident it seems like they’re rather incompetent unfortunately so I’d like some advice on this!

Thanks :)

#update x1

Spoke to the shop again and fished a bit for info. Guy at the desk re-confirmed that the gaiter was busted when I went there, and got rather apologetic when I pointed out that it wasn’t.

They claim that they did notice the lifter tick but said that “it’s common for older cars but you don’t need to worry about it, and it’s a lot of work to fix it”, hence why they didn’t point it out.

I’ll probably postpone looking into this fully until after the road trip.

It’s a 4-cyl I4 petrol engine ('95 Mazda 626) with a ticking noise that matches with revs. I’ve had it for a while and it seems to be getting louder as time goes on. It doesn’t go away even after longer drives.

The workshop I’ve used previously haven’t highlighted it when I had the car in for an inspection, but after a recent incident it seems like they’re rather incompetent unfortunately so I’d like some advice on this!

Thanks :)

#update x1

Spoke to the shop again and fished a bit for info. Guy at the desk re-confirmed that the gaiter was busted when I went there, and got rather apologetic when I pointed out that it wasn’t.

They claim that they did notice the lifter tick but said that “it’s common for older cars but you don’t need to worry about it, and it’s a lot of work to fix it”, hence why they didn’t point it out.

I’ll probably postpone looking into this fully until after the road trip.

0

2022 Hyundai Palisade - wrong brake pads

preview

I changed my brake pads and realized at the end I may have swapped the inner and outer pads on the rear tires. I’m not 100% sure but I think the piston in one of the tires is pressing against the black pins like the top pad in the picture.

Should I correct this immediately or can I get by until my next change?

I changed my brake pads and realized at the end I may have swapped the inner and outer pads on the rear tires. I’m not 100% sure but I think the piston in one of the tires is pressing against the black pins like the top pad in the picture.

Should I correct this immediately or can I get by until my next change?

0

2014 GMC Savanah keep backup camera on all the time

preview

I drive a 2014 GMC Savanah cargo van for work. It has a handy backup camera display built into the rearview mirror. However the camera is only on when the truck is in reverse. Seeing as how this is a cargo van with a solid wall directly behind the seats, the rearview mirror is useless for anything besides that backup camera display and checking my hair. I figure if I could get it to leave the backup camera on whenever the truck is on then I could also see whatever is directly behing me when just driving normally far more effectively than I can with just the side mirrors.

Is there any way to just keep the backup camera on whenenever the truck is on? Is there any reason why doing so would be a bad idea?

I drive a 2014 GMC Savanah cargo van for work. It has a handy backup camera display built into the rearview mirror. However the camera is only on when the truck is in reverse. Seeing as how this is a cargo van with a solid wall directly behind the seats, the rearview mirror is useless for anything besides that backup camera display and checking my hair. I figure if I could get it to leave the backup camera on whenever the truck is on then I could also see whatever is directly behing me when just driving normally far more effectively than I can with just the side mirrors.

Is there any way to just keep the backup camera on whenenever the truck is on? Is there any reason why doing so would be a bad idea?

0

'99 Corolla engine code P0125

preview

I’m trying to diagnose a p0125 code on my 99 corolla. Toyota forums seem to say Toyota didn’t follow standards on this code and it is likely also the O2 sensor, can anyone confirm if this is the case?

I’m getting no other codes, and it will run for about 30 minutes before triggering again. Last time it triggered I saw exhaust smoke on the way home, which went away as soon as I reset the code. after clearing the code the exhaust while clear does seem to be rich smelling. Engine seems to run fine, I’m not noticing any performance issues, not signs of dipping oil/coolant amounts. coolant gauge is operating and hitting the halfway point normally.

I can’t think of anything else but the O2 sensor but I expected rougher performance and don’t really want to spend $125 on a part if I don’t have to.

I’m trying to diagnose a p0125 code on my 99 corolla. Toyota forums seem to say Toyota didn’t follow standards on this code and it is likely also the O2 sensor, can anyone confirm if this is the case?

I’m getting no other codes, and it will run for about 30 minutes before triggering again. Last time it triggered I saw exhaust smoke on the way home, which went away as soon as I reset the code. after clearing the code the exhaust while clear does seem to be rich smelling. Engine seems to run fine, I’m not noticing any performance issues, not signs of dipping oil/coolant amounts. coolant gauge is operating and hitting the halfway point normally.

I can’t think of anything else but the O2 sensor but I expected rougher performance and don’t really want to spend $125 on a part if I don’t have to.

0

2004 Volvo v70 2.5t frw dies immediately after it starts

preview

Car was running fine, parked for a week or so and now dies immediately after start (doesn’t stop like it’s low on fuel, stops like if I were to turn the ignition to off). No amount of throttle changes this behavior. I did some Internet research and found that disconnecting the MAF sensor might lead me to the cause if it runs after disconnect. Exact same behavior when disconnected. While in the engine bay I found that if I disconnected the Boost Pressure Solenoid, it started up and ran (idle was a little high, but seems to run okay). The fact it’s running when that solenoid is disconnected leads me to believe it’s not (at least entirely) a fuel delivery issue. Would you expect that the solenoid itself is the issue, or does that lead you to expect it’s some other issue.

Some background history that MIGHT be helpful. Radiator cracked sometime last year (saw low coolant light and stopped before engine got hot), finally got it replaced in Jan or Feb. Took for a test drive and was running fine, then stalled on us right as we left the neighborhood. (Threw a fuel delivery code, but only once, and I didn’t take a pic. Didn’t show in history or active codes) Would not start. If it did start, would die shortly after (felt and seemed like fuel delivery issues, with a sputter stop). Let it sit a few minutes, and then was able to drive it home without issue. Have since driven it far and at freeway speeds without issues.

Car shows 2 engine codes, will provide images in comments.

P0140 P0141

Stored codes P0036 P0140 P0141

None of these are NEW codes, it was running “fine” with them.

Car was running fine, parked for a week or so and now dies immediately after start (doesn’t stop like it’s low on fuel, stops like if I were to turn the ignition to off). No amount of throttle changes this behavior. I did some Internet research and found that disconnecting the MAF sensor might lead me to the cause if it runs after disconnect. Exact same behavior when disconnected. While in the engine bay I found that if I disconnected the Boost Pressure Solenoid, it started up and ran (idle was a little high, but seems to run okay). The fact it’s running when that solenoid is disconnected leads me to believe it’s not (at least entirely) a fuel delivery issue. Would you expect that the solenoid itself is the issue, or does that lead you to expect it’s some other issue.

Some background history that MIGHT be helpful. Radiator cracked sometime last year (saw low coolant light and stopped before engine got hot), finally got it replaced in Jan or Feb. Took for a test drive and was running fine, then stalled on us right as we left the neighborhood. (Threw a fuel delivery code, but only once, and I didn’t take a pic. Didn’t show in history or active codes) Would not start. If it did start, would die shortly after (felt and seemed like fuel delivery issues, with a sputter stop). Let it sit a few minutes, and then was able to drive it home without issue. Have since driven it far and at freeway speeds without issues.

Car shows 2 engine codes, will provide images in comments.

P0140 P0141

Stored codes P0036 P0140 P0141

None of these are NEW codes, it was running “fine” with them.

0

What's the name of this (metal?) alloy?

preview

This is usually found in really cheap products and looks and sounds metallic (rings a bit when dropped) , but I’m not sure if it is one.

The pictured cross section shows the greyish metal (the gold is just paint).

The cross section feels coarse and has tiny glittering specks. It also looks a bit porous (tiny air bubbles seem to be present in this alloy)

It’s also pretty weak - a pencil like object made from this stuff can easily be snapped in two with your bare hands.

Thanks!

This is usually found in really cheap products and looks and sounds metallic (rings a bit when dropped) , but I’m not sure if it is one.

The pictured cross section shows the greyish metal (the gold is just paint).

The cross section feels coarse and has tiny glittering specks. It also looks a bit porous (tiny air bubbles seem to be present in this alloy)

It’s also pretty weak - a pencil like object made from this stuff can easily be snapped in two with your bare hands.

Thanks!

0

Follow-Up - Alignment Off - 2019 Atlas

preview

Hi again. I took the car back to the dealer to re-align and the wheel is still turned to the left a little when driving straight. The tech showed me the numbers and that they leveled the steering wheel.

Is something wrong with my suspension, or should I try alignment somewhere else? Just live with it?

EDIT: when I let the wheel go and I’m going straight on a stretch of road the wheel is off center by about 10 degrees.

EDIT EDIT: called the dealership and they said alignment doesn’t include resetting wheel sensor via obd tool. Crazy.

Hi again. I took the car back to the dealer to re-align and the wheel is still turned to the left a little when driving straight. The tech showed me the numbers and that they leveled the steering wheel.

Is something wrong with my suspension, or should I try alignment somewhere else? Just live with it?

EDIT: when I let the wheel go and I’m going straight on a stretch of road the wheel is off center by about 10 degrees.

EDIT EDIT: called the dealership and they said alignment doesn’t include resetting wheel sensor via obd tool. Crazy.

0

Why can't any shop/dealership I've been to do an alignment right?

preview

I’ve been to smaller shops, I’ve been to dealerships, and the only time I’ve ever gotten an alignment done right was after I complained to a general manager. I know alignments are hard with the laser machines. It shouldn’t be a problem, right? Are they just being lazy? I hate having to go back to the shop and wait another 2 to 4 hours to get something done that should’ve been done right the first time.

EDIT: I’ve had this happen with my 2001 QX4 4WD, 2019 Q50 2WD and now with 2019 Atlas AWD

I’ve been to smaller shops, I’ve been to dealerships, and the only time I’ve ever gotten an alignment done right was after I complained to a general manager. I know alignments are hard with the laser machines. It shouldn’t be a problem, right? Are they just being lazy? I hate having to go back to the shop and wait another 2 to 4 hours to get something done that should’ve been done right the first time.

EDIT: I’ve had this happen with my 2001 QX4 4WD, 2019 Q50 2WD and now with 2019 Atlas AWD

0

Is it as bad as I think it is?

preview

Sorry for the bad image quality.

The image is of the top of piston 4 and the cylinder wall in a Toyota 2AR-FE with 162,000 miles. All Toyota recommended maintenance was performed throughout the engine’s life. I have the feeling those recommendations were written by marketing people and not the engineers.

Based on what the image shows, the engine needs a short block. Am I correct?

Sorry for the bad image quality.

The image is of the top of piston 4 and the cylinder wall in a Toyota 2AR-FE with 162,000 miles. All Toyota recommended maintenance was performed throughout the engine’s life. I have the feeling those recommendations were written by marketing people and not the engineers.

Based on what the image shows, the engine needs a short block. Am I correct?

0

Bad electrical component draining battery?

preview

I’ve acquired a classic 1977 124 Spider that hasn’t seen much action in ~1 decade. I’ve had it ~1 week & the most important stuff works. I’ve done a number of small trips around town. Yesterday in the garage I wanted to catalog everything that needs repair by flipping all knobs/switches and marking what’s not working. I found that the wipers don’t work (but the wiper fluid pump does) and the cabin air/defrost fan doesn’t come on, and one of the air levers is locked/frozen. I left the car for a couple of hours and when I returned I thought I could smell plastic burning. I hunted for the smell & found a small electronic component under the hood that seemed like it might be hot, but I wasn’t sure. I left the car overnight with the hood up and when I returned I the smell was gone but the battery was dead!

I figured I must have left something on by mistake so I went through all knobs/controls using the owner’s manual to make certain that everything off (it was). Then I jumped the car & drove it around for ~20 minutes. Left it in the garage ~1 hour being very careful that the doors were closed, no lights were on, etc. & checked on it to see if the burning smell returned (it hadn’t). Left it overnight & in the morning it was dead again!

I don’t think that there’s anything wrong with the battery or alternator because it had run fine all week with multiple short trips around town. I think it’s more likely that an electrical component is shorting somewhere & draining the battery. Perhaps turning knobs & flipping switches pushed an old brittle electrical part over the edge?

My question is: what is the best way to find the malfunctioning electrical component? I was thinking of the following:

  • Jump the car & recharge battery by driving around town

  • Park in the garage and disconnect all fuses

  • Return every ~8 hours and check the battery, if it looks OK then replace a fuse

  • Repeat the above step until the battery dies

Using that approach I can isolate the bad component to the circuit running through that fuse. It’s a slow process though, is there a faster or more efficient way to do this? Any other ideas as to root cause? Any thoughts appreciated, thanks!

I’ve acquired a classic 1977 124 Spider that hasn’t seen much action in ~1 decade. I’ve had it ~1 week & the most important stuff works. I’ve done a number of small trips around town. Yesterday in the garage I wanted to catalog everything that needs repair by flipping all knobs/switches and marking what’s not working. I found that the wipers don’t work (but the wiper fluid pump does) and the cabin air/defrost fan doesn’t come on, and one of the air levers is locked/frozen. I left the car for a couple of hours and when I returned I thought I could smell plastic burning. I hunted for the smell & found a small electronic component under the hood that seemed like it might be hot, but I wasn’t sure. I left the car overnight with the hood up and when I returned I the smell was gone but the battery was dead!

I figured I must have left something on by mistake so I went through all knobs/controls using the owner’s manual to make certain that everything off (it was). Then I jumped the car & drove it around for ~20 minutes. Left it in the garage ~1 hour being very careful that the doors were closed, no lights were on, etc. & checked on it to see if the burning smell returned (it hadn’t). Left it overnight & in the morning it was dead again!

I don’t think that there’s anything wrong with the battery or alternator because it had run fine all week with multiple short trips around town. I think it’s more likely that an electrical component is shorting somewhere & draining the battery. Perhaps turning knobs & flipping switches pushed an old brittle electrical part over the edge?

My question is: what is the best way to find the malfunctioning electrical component? I was thinking of the following:

  • Jump the car & recharge battery by driving around town

  • Park in the garage and disconnect all fuses

  • Return every ~8 hours and check the battery, if it looks OK then replace a fuse

  • Repeat the above step until the battery dies

Using that approach I can isolate the bad component to the circuit running through that fuse. It’s a slow process though, is there a faster or more efficient way to do this? Any other ideas as to root cause? Any thoughts appreciated, thanks!

0

Diagnosing A/C Failure When Idling

preview

2001 QX4

It has been 90+ degrees where I live and when idling for more than 10-15 min, the A/C stops blowing cold and is humid. Works great otherwise when ambient temps are low and car is moving. The Freon pressure is good. The Enser is old and has some dents, but has been cleaned and looks to be getting airflow. How can I tell what is wrong? Replace the radiator fan clutch? Condenser? Something else? Should also note that the engine temp gets high when on long stretches up uphill highway, but I think that is somewhat normal for an old car, no? Thanks!

2001 QX4

It has been 90+ degrees where I live and when idling for more than 10-15 min, the A/C stops blowing cold and is humid. Works great otherwise when ambient temps are low and car is moving. The Freon pressure is good. The Enser is old and has some dents, but has been cleaned and looks to be getting airflow. How can I tell what is wrong? Replace the radiator fan clutch? Condenser? Something else? Should also note that the engine temp gets high when on long stretches up uphill highway, but I think that is somewhat normal for an old car, no? Thanks!

0

New rotors and semi metallic pads. Rubbing/vibratong noise when coming to complete stop and when lifting off pedal from complete stop.

preview

Just replaced the rotors and new pads. The pads are semi metallic. I’ve noticed a brief rubbing sound when coming to a complete stop and when lifting my foot off the brake pedal from a stop. Is this normal for metallic pads?

Just replaced the rotors and new pads. The pads are semi metallic. I’ve noticed a brief rubbing sound when coming to a complete stop and when lifting my foot off the brake pedal from a stop. Is this normal for metallic pads?

0

Put single new tire in front open diff or rear weak LSD (~60lb breakaway)

preview

2001 Infiniti QX4 Automatic 4WD with RWD bias (4WD only kicks in when rear slips)

Had to replace one tire. Should new tire be on front with open diff or rear with LSD rated around 60lb breakaway torque?

The rest of the tires have about 60% tread left. Less than 15k miles on them.

I’m thinking front but want to make sure it won’t cause pulling to one side or mess something up.

Thanks!

EDIT: I know I should do pairs. Wondering if anybody had an opinion if I just kept the one.

2001 Infiniti QX4 Automatic 4WD with RWD bias (4WD only kicks in when rear slips)

Had to replace one tire. Should new tire be on front with open diff or rear with LSD rated around 60lb breakaway torque?

The rest of the tires have about 60% tread left. Less than 15k miles on them.

I’m thinking front but want to make sure it won’t cause pulling to one side or mess something up.

Thanks!

EDIT: I know I should do pairs. Wondering if anybody had an opinion if I just kept the one.

0

Should I get this bent wheel repaired?

preview

So, a few months ago I ran into a pothole and got a bubble on my tyre. It was almost time to switch to winter tyres so I kept driving for a few more weeks with no issues, put winters on and that was that. Today I went to get the summers installed and replace the one with the bubble and the mechanic pointed out that I also bent the rim on that pothole. I hadn’t noticed the damage, nor any vibrations and it’s still holding air perfectly. It’s now mounted in the rear, where it will hopefully be under less stress (I drive a Yaris). I can get a new wheel, but not for the next few weeks and I do need to drive in the meantime, so my question is, should I bother getting this wheel repaired? The damage doesn’t seem big and from what I’ve heard straightening aluminium wheels sometimes leads to cracks, which will just make the situation worse than it already is. I’d rather have a wheel that’s probably usable than one that definitely isn’t.

Edit: I should point out, the winter tyres are on a different set of rims. I’ve only driven on this wheel for about 2 weeks, from when I hit the pothole until I had the winter tyres installed. Today I had it put back on the car and the mechanic pointed out the damage to me.

So, a few months ago I ran into a pothole and got a bubble on my tyre. It was almost time to switch to winter tyres so I kept driving for a few more weeks with no issues, put winters on and that was that. Today I went to get the summers installed and replace the one with the bubble and the mechanic pointed out that I also bent the rim on that pothole. I hadn’t noticed the damage, nor any vibrations and it’s still holding air perfectly. It’s now mounted in the rear, where it will hopefully be under less stress (I drive a Yaris). I can get a new wheel, but not for the next few weeks and I do need to drive in the meantime, so my question is, should I bother getting this wheel repaired? The damage doesn’t seem big and from what I’ve heard straightening aluminium wheels sometimes leads to cracks, which will just make the situation worse than it already is. I’d rather have a wheel that’s probably usable than one that definitely isn’t.

Edit: I should point out, the winter tyres are on a different set of rims. I’ve only driven on this wheel for about 2 weeks, from when I hit the pothole until I had the winter tyres installed. Today I had it put back on the car and the mechanic pointed out the damage to me.

0

[FWD Manual] Gear selection problem

preview

Can anyone suggest what might be wrong? I have just changed the clutch and now I am struggling to select gears even when the engine isn’t running.

I don’t think it’s linkage related because it seems to be difficult to select gears just pulling directly on the arms that move the forks too. I don’t think I’ve done anything that should have an effect on the inside of the gearbox, I’ve removed and refitted the drive shafts and changed the fluid.

Also can anyone confirm my thinking that the clutch and concentric slave cylinder shouldn’t be a factor, since the problem exists when the engine isn’t running?

Edit: Strangely, after leaving it overnight, gears are selecting perfectly again and I have absolutely no idea why. I didn’t change anything 😕

I suppose that should be good news but without knowing what the problem was, I’m not very satisfied. Thank you to everyone for your help.

Can anyone suggest what might be wrong? I have just changed the clutch and now I am struggling to select gears even when the engine isn’t running.

I don’t think it’s linkage related because it seems to be difficult to select gears just pulling directly on the arms that move the forks too. I don’t think I’ve done anything that should have an effect on the inside of the gearbox, I’ve removed and refitted the drive shafts and changed the fluid.

Also can anyone confirm my thinking that the clutch and concentric slave cylinder shouldn’t be a factor, since the problem exists when the engine isn’t running?

Edit: Strangely, after leaving it overnight, gears are selecting perfectly again and I have absolutely no idea why. I didn’t change anything 😕

I suppose that should be good news but without knowing what the problem was, I’m not very satisfied. Thank you to everyone for your help.

0

Rear tie rods for Mitsubishi Pajero/Montero?

Imgur imgur.com i.imgur.com
preview

Hi all! My very old Mitsubishi Pajero III (V60 from 2000) got a 2" lift kit and now the rear wheels have too much toe-out. The stock tie rods won’t adjust far enough and there are no other original “sizes.”

So I need some aftermarket tie rods for the rear axle. My own research tells me I need a shorter (longer?) version of the original part number MR508134 (Imgur).

Two questions:

  • Am I correct that the rear toe angle is adjusted via this part?
  • Given that the stock MR508134 is no sufficiently adjustable, what sort of aftermarket part should I be looking for? I’m in Europe.

(For the sake of completeness: the front tie rods have adequate adjustment range.)

Hi all! My very old Mitsubishi Pajero III (V60 from 2000) got a 2" lift kit and now the rear wheels have too much toe-out. The stock tie rods won’t adjust far enough and there are no other original “sizes.”

So I need some aftermarket tie rods for the rear axle. My own research tells me I need a shorter (longer?) version of the original part number MR508134 (Imgur).

Two questions:

  • Am I correct that the rear toe angle is adjusted via this part?
  • Given that the stock MR508134 is no sufficiently adjustable, what sort of aftermarket part should I be looking for? I’m in Europe.

(For the sake of completeness: the front tie rods have adequate adjustment range.)

0

Been a while! Connecting an AC fan motor to a compressor?

preview

Hope y’all are still doing okay! Personally I’ve been a little off for a few months but that’s okay.

Now, I have, as I’m assuming everyone does (I live in a junkyard don’t blame me) AC you fan motors that I am looking to use as generators all connected to my compressor.

Took a fan apart and realized that… I have a generator!

Any advice on the ins and outs? I mean, it works and produces a solid half an amp according to the multimeter but how should I hook it up?

What else do I need? Guaranteed I have everything needed just need to know what to look for.

What I’m using it for? Maybe just some lights on the compressor? Maybe a phone charger addon or something? What would I need to do either aside from just hooking it up like I am about to do?

Hope y’all are still doing okay! Personally I’ve been a little off for a few months but that’s okay.

Now, I have, as I’m assuming everyone does (I live in a junkyard don’t blame me) AC you fan motors that I am looking to use as generators all connected to my compressor.

Took a fan apart and realized that… I have a generator!

Any advice on the ins and outs? I mean, it works and produces a solid half an amp according to the multimeter but how should I hook it up?

What else do I need? Guaranteed I have everything needed just need to know what to look for.

What I’m using it for? Maybe just some lights on the compressor? Maybe a phone charger addon or something? What would I need to do either aside from just hooking it up like I am about to do?

0

Cleaning engine bay/ miscellaneous crannies

preview

So, that insight we bought last September so far seems mechanically sound, but, so, so dirty. I’m not sure how best to approach it but waiting till spring because our garage is not heated and it’s cold as shit up here in MT.

My biggest concern is safely removing all the little mouse poops that are literally everywhere except in the cabin. I fashioned a cardboard cone with gorilla tape to our shitty shop vac to clean out the spare tire well but I’ll probably need a smaller cylinder to reach them in the engine bay and battery compartment. On top of that it seems like dirt/dust is underneath all the trim. I believe the previous owner lived off a gravel/dirt road. It’s the kind of dirt that doesn’t wipe away the first time, and I don’t want to ruin the dash/plastic/vinyl miscellany with harsh chemicals.

Insight is mostly aluminum so I need to double check cleaning methods to avoid. I’ve taken dish soap+bronze/plastic brushes to the back of the wheels (also aluminum)but sandpaper has been better. Haven’t touched the front of the wheels with the sandpaper as it seems to have a gloss coat of some sort on it and would prefer to have its replacement on hand before removing it.

Ideas?

So, that insight we bought last September so far seems mechanically sound, but, so, so dirty. I’m not sure how best to approach it but waiting till spring because our garage is not heated and it’s cold as shit up here in MT.

My biggest concern is safely removing all the little mouse poops that are literally everywhere except in the cabin. I fashioned a cardboard cone with gorilla tape to our shitty shop vac to clean out the spare tire well but I’ll probably need a smaller cylinder to reach them in the engine bay and battery compartment. On top of that it seems like dirt/dust is underneath all the trim. I believe the previous owner lived off a gravel/dirt road. It’s the kind of dirt that doesn’t wipe away the first time, and I don’t want to ruin the dash/plastic/vinyl miscellany with harsh chemicals.

Insight is mostly aluminum so I need to double check cleaning methods to avoid. I’ve taken dish soap+bronze/plastic brushes to the back of the wheels (also aluminum)but sandpaper has been better. Haven’t touched the front of the wheels with the sandpaper as it seems to have a gloss coat of some sort on it and would prefer to have its replacement on hand before removing it.

Ideas?

0

Volvo V40 1995 / headlight not working / Bulb and fuse working

preview

Hello, just wanted to let you all know how to fix a dead headlight on the 1st gen Volvo S40/V40. Maybe even other similar models. This is in the event that your bulb and fuse are fine. The headlights are automatic and wired to a relay.

Some genius decided to make the auto headlight relay soldered onto the CEM module under the steering wheel.

You can find it after stripping the plastics, and it should be clearly labeled in some corner.

Opening it reveals all these relays. You need the center 2. They are 12V SPDT 1 form C. The center is for the right headlight, and the one next to it (the orange one I put there) is for the left headlight.

Barely a buck/euro in parts cost. My fingers froze while opening the car though.

Of course, Volvo could have made these easier to replace, but they did last a fair bit either way.

Hello, just wanted to let you all know how to fix a dead headlight on the 1st gen Volvo S40/V40. Maybe even other similar models. This is in the event that your bulb and fuse are fine. The headlights are automatic and wired to a relay.

Some genius decided to make the auto headlight relay soldered onto the CEM module under the steering wheel.

You can find it after stripping the plastics, and it should be clearly labeled in some corner.

Opening it reveals all these relays. You need the center 2. They are 12V SPDT 1 form C. The center is for the right headlight, and the one next to it (the orange one I put there) is for the left headlight.

Barely a buck/euro in parts cost. My fingers froze while opening the car though.

Of course, Volvo could have made these easier to replace, but they did last a fair bit either way.

0

[2018 Nissan Qashqai] Metal plate (splash guard?) has come loose

preview

It’s completely loose (can move a few inches up and down) and rattles on the muffler while driving. Easy fix for a noob, or should I take it in? And uh… how urgently? 😂

It’s completely loose (can move a few inches up and down) and rattles on the muffler while driving. Easy fix for a noob, or should I take it in? And uh… how urgently? 😂

0

Can I replace only one tire if the other 3 aren't very worn?

preview

For context, I drive a Toyota Yaris on 17 inch wheels. I hit a pothole and got a bubble on my front right tire (the pain of running low profile tires). Anyway, I bough these tires something like 6 months ago and only have 5000-ish kilometers on them. The other 3 still look in perfect condition. I know it’s normally recommended to replace tires in pairs, but is that really needed here considering how new the set is? Feels stupid to replace a tire that is practically new.

For context, I drive a Toyota Yaris on 17 inch wheels. I hit a pothole and got a bubble on my front right tire (the pain of running low profile tires). Anyway, I bough these tires something like 6 months ago and only have 5000-ish kilometers on them. The other 3 still look in perfect condition. I know it’s normally recommended to replace tires in pairs, but is that really needed here considering how new the set is? Feels stupid to replace a tire that is practically new.

0

Gas smell only on cold start?

preview

I drive a 2008 4runner with 85k miles. It’s been receiving by the manual maintenance for its whole life.

Recently I have started noticing a gas smell when I start the car in the morning. It seems to dissipate after a few minutes. I also don’t really notice it on subsequent starts on the same day if I take the car out multiple times. Or if I do, it’s less pronounced.

There is no visible leak or gas on the driveway that I can see.

Any ideas? I’m planning to take it in but figured no harm in asking here to see if anyone knows what I might be dealing with first.

Thanks!

I drive a 2008 4runner with 85k miles. It’s been receiving by the manual maintenance for its whole life.

Recently I have started noticing a gas smell when I start the car in the morning. It seems to dissipate after a few minutes. I also don’t really notice it on subsequent starts on the same day if I take the car out multiple times. Or if I do, it’s less pronounced.

There is no visible leak or gas on the driveway that I can see.

Any ideas? I’m planning to take it in but figured no harm in asking here to see if anyone knows what I might be dealing with first.

Thanks!

0

okay, this time I actually need mechanic advice.

play · i.imgur.com
Imgur imgur.com imgur.com
preview

I think it defaults as muted but I included sound. Pardon the party music, the construction guys near the parking lot were having a blast today lol. Anyway. It’s been cold as fuck the past couple days and this noise only happens on start after sitting several hours cold. I’m guessing either starter or belts but haven’t gone investigating yet.

I think it defaults as muted but I included sound. Pardon the party music, the construction guys near the parking lot were having a blast today lol. Anyway. It’s been cold as fuck the past couple days and this noise only happens on start after sitting several hours cold. I’m guessing either starter or belts but haven’t gone investigating yet.